|
|
#1 |
|
Noob-Jersey
|
3000GT Engine rebuild
Last edited by catchme215; 07-12-2010 at 10:54 PM. |
|
|
|
|
|
#2 |
|
Tri-State Addict
Join Date: Jul 2010
Location: The person who invented the light bulb,NJ
Member #16900
My Ride: Turboless BMW e92 iTrader: (0)
|
my suggestion you should go on 3si.com and ask them, they prob. recommend to go here 3sx.com
__________________
Instagram: @ThaiBMW 97 Honda Civic-Sold 02 Lexus is300-Sold 00 BMW 323ci e46-Totaled To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. 07 BMW 328xi e92 To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. |
|
|
|
|
|
#3 | |
|
Tri-State Post Whore
Banned
Join Date: Jan 2009
Location: all over
Member #10595
My Ride: Does not hit mivec anymore.(DD) 06 solstice 5 speed. 84 IMSA Fiero5 speed. 87 Fiero GT 5 speed iTrader: (0)
|
Quote:
Whats it doin? If it rod bearings i would sugest getting a new motor. |
|
|
|
|
|
|
#4 |
|
TST Ruined My Life!
|
I have a block you can have if you pick it up(it has been sitting outside the garage for awhile so its dirty but some TLC and you will have a nice blank canvas to start your rebuild). Friend of ours snapped his timing belt and just gout a new motor. Block is good, heads are good, but since it is an interference motor you obvoiiusly know the damage but the casting are OK. It is from a Stealth R/T non turbo with about 140k miles.
__________________
2014 Mustang GT performance package, M6, Brembo brakes, Torsen diff with 3.73, Steeda CAI with 101mm MAF, ST coilovers with caster/camber plates, BMR lower control arms, BMR watts link, BMW sway bars with end links, front brake cooling ducts, SR short shiffter, and custom tuned |
|
|
|
|
|
#5 | |
|
Tri-State Post Whore
Banned
Join Date: Jan 2009
Location: all over
Member #10595
My Ride: Does not hit mivec anymore.(DD) 06 solstice 5 speed. 84 IMSA Fiero5 speed. 87 Fiero GT 5 speed iTrader: (0)
|
Quote:
I wouldent recomend rebuilding yours depending on what happend you could have small microscopic metal shavings inside your motor that will drasticley reduce the life of the motor if you rebuild it. |
|
|
|
|
|
|
#6 | |
|
Tri-State Post Whore
|
Are you turbo or non-turbo? I'm going to assume turbo, most N/A's don't throw rods through the block, lol. The stock turbo engine can take up to 500awhp on a mediocre tune, on a really good tune, you can expect 600awhp to hold up for a pretty long time. The rods/pistons are the weakest parts. The second gen ring land height is short, and any large knock counts tends to blow them up.
Non-turbo engines are notably weaker. This is definitely a post that can go on 3si, there's not many 3s owners on TST. Quote:
|
|
|
|
|
|
|
#7 | |
|
TST Ruined My Life!
|
Quote:
__________________
2014 Mustang GT performance package, M6, Brembo brakes, Torsen diff with 3.73, Steeda CAI with 101mm MAF, ST coilovers with caster/camber plates, BMR lower control arms, BMR watts link, BMW sway bars with end links, front brake cooling ducts, SR short shiffter, and custom tuned Last edited by jpalamar; 07-13-2010 at 03:59 PM. |
|
|
|
|
|
|
#9 |
|
Noob-Jersey
|
lol, it's actually N/A but i was looking to see what my options were. I want to turbo it, and also see if forged rods/pistons were recommended let alone a possibility. With it being non-turbo, what do you suggest as far as upgrades?
|
|
|
|
|
|
#10 |
|
TST Ruined My Life!
|
Yea, block is in Boyertown. Unfortunatly, I don't know anything about those cars though.
__________________
2014 Mustang GT performance package, M6, Brembo brakes, Torsen diff with 3.73, Steeda CAI with 101mm MAF, ST coilovers with caster/camber plates, BMR lower control arms, BMR watts link, BMW sway bars with end links, front brake cooling ducts, SR short shiffter, and custom tuned |
|
|
|
|
|
#12 |
|
TST Ruined My Life!
|
I just sent you a PM.
__________________
2014 Mustang GT performance package, M6, Brembo brakes, Torsen diff with 3.73, Steeda CAI with 101mm MAF, ST coilovers with caster/camber plates, BMR lower control arms, BMR watts link, BMW sway bars with end links, front brake cooling ducts, SR short shiffter, and custom tuned |
|
|
|
|
|
#13 | |
|
Tri-State Post Whore
|
Quote:
If you're going with a TT conversion, you'll want to drop the compression ratio using either stock TT parts, or aftermarket. |
|
|
|
|
|
|
#15 |
|
Tri-State Post Whore
|
Go with forged internals at the TT's 8:1 comp ratio. I'd suggest a TT conversion first, and a trans swap to a modded Getrag, the FWD trans can't take the power.
|
|
|
|
|
|
#18 | |
|
Tri-State Addict
|
Quote:
Rebuilds are a nightmare, especially if you have no experience. If it's a spun bearing... you'll need a crankshaft... that alone, brand new, is $750. I can sell you a complete running engine, for $800.
__________________
1991 Stealth R/T Twin Turbo, 1995 3000GT Spyder, 1995 3000GT VR-4, 1995 Stealth R/T Twin Turbo, 1996 Dodge Ram V10 2500, etc... |
|
|
|
|
|
|
#19 | |
|
Tri-State Addict
|
Quote:
Keep it fwd, N/A. Fix it, and if you want turbo, sell it and buy a vr4. The pricing on Vr4's right now is silly cheap... MUCH less than you'll spend on converting yours to twin turbo, blah de blah, and you'll still be FWD.
__________________
1991 Stealth R/T Twin Turbo, 1995 3000GT Spyder, 1995 3000GT VR-4, 1995 Stealth R/T Twin Turbo, 1996 Dodge Ram V10 2500, etc... |
|
|
|
|
|
|
#20 | |
|
Tri-State Post Whore
|
Quote:
|
|
|
|
|
![]() |
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Engine Codes after Grand AM Rebuild. | zuki19 | General Car Related Chat | 18 | 06-08-2010 04:12 PM |
| Engine rebuild -WRX | SMOCAN | Subaru Talk | 9 | 05-06-2009 07:29 PM |
| Engine Rebuild | AutobahnRacer | Honda / Acura Talk | 2 | 05-26-2007 04:01 PM |
| Rebuild OR New Engine??? | SUB2.5RS | General Car Related Chat | 15 | 12-02-2006 10:35 AM |
| Engine rebuild? | charliemopps24 | Engine Performance | 2 | 11-30-2006 03:06 AM |