![]() |
3000GT Engine rebuild
I own a '95 3000GT and I blew my engine months back. I haven't had a chance to tear it apart and see what the problem is, but I'm almost sure there's a hole in the block. I'm looking to rebuild the engine very soon, that is if there isn't a hole in the block, and I had some general questions. As far as rods and pistons, how much power can the stock ones hold? Does anybody recommend forged pistons/rods? And what is the weakest point on the motor? Any other comments and suggestions are welcome.
|
my suggestion you should go on 3si.com and ask them, they prob. recommend to go here 3sx.com
|
Quote:
Whats it doin? If it rod bearings i would sugest getting a new motor. |
I have a block you can have if you pick it up(it has been sitting outside the garage for awhile so its dirty but some TLC and you will have a nice blank canvas to start your rebuild). Friend of ours snapped his timing belt and just gout a new motor. Block is good, heads are good, but since it is an interference motor you obvoiiusly know the damage but the casting are OK. It is from a Stealth R/T non turbo with about 140k miles.
|
Quote:
I wouldent recomend rebuilding yours depending on what happend you could have small microscopic metal shavings inside your motor that will drasticley reduce the life of the motor if you rebuild it. |
Are you turbo or non-turbo? I'm going to assume turbo, most N/A's don't throw rods through the block, lol. The stock turbo engine can take up to 500awhp on a mediocre tune, on a really good tune, you can expect 600awhp to hold up for a pretty long time. The rods/pistons are the weakest parts. The second gen ring land height is short, and any large knock counts tends to blow them up.
Non-turbo engines are notably weaker. This is definitely a post that can go on 3si, there's not many 3s owners on TST. Quote:
|
Quote:
|
Is the engine located in Boyertown? Since it's sitting outside your garage, I would definitely like to pick it up since I'm having trouble finding a block.
|
lol, it's actually N/A but i was looking to see what my options were. I want to turbo it, and also see if forged rods/pistons were recommended let alone a possibility. With it being non-turbo, what do you suggest as far as upgrades?
|
Yea, block is in Boyertown. Unfortunatly, I don't know anything about those cars though.
|
When is it possible to pick it up? The earliest I can do is probably Sunday. Let me know your availability.
|
I just sent you a PM.
|
Quote:
If you're going with a TT conversion, you'll want to drop the compression ratio using either stock TT parts, or aftermarket. |
How about a single turbo?
|
Go with forged internals at the TT's 8:1 comp ratio. I'd suggest a TT conversion first, and a trans swap to a modded Getrag, the FWD trans can't take the power.
|
Docwalt, what are you running in your vr4?
|
Stock pretty much everything. IPS Downpipe, and a ported/fixed eBay header. Oh boy, lol
|
Quote:
Rebuilds are a nightmare, especially if you have no experience. If it's a spun bearing... you'll need a crankshaft... that alone, brand new, is $750. I can sell you a complete running engine, for $800. |
Quote:
Keep it fwd, N/A. Fix it, and if you want turbo, sell it and buy a vr4. The pricing on Vr4's right now is silly cheap... MUCH less than you'll spend on converting yours to twin turbo, blah de blah, and you'll still be FWD. |
Quote:
|
| All times are GMT -4. The time now is 09:51 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.