The Govenator say Hondata Heatshields, Thermalnator, Apex-i Phenolic Gaskets Rule! - TriStateTuners.com :: Home of Tristate Auto Enthusiast

S.Milone · 07-11-2007, 04:15 PM

Hondata Heatshields, Thermalnator, Apex I Phenolic gasket
Even the Governator says it cools your intake air.

Hondata Heat Shields

The Heatshield is a replacement intake manifold gasket made from special high temperature plastic, designed to insulate the intake manifold from the cylinder head.

Hondata have developed a special high temperature insulating gasket which replaces the stock intake gasket. This and bypassing several heat sources significantly reduces the transfer of heat from the head to the intake and incoming air giving you up to 5% more power.
Turbocharged cars often use an aluminum intercooler to cool the air compressed by the turbo. The intake manifold is also made of aluminum but because it is heated by the head from combustion, works in reverse to an intercooler by heating the intake air by as much as 50° C.
Fact: For every 3.3 °C (5° F) rise in intake temperature, air density drops 1%. The hotter the air, the less fuel the computer injects to compensate for reduced oxygen. HondaLogger datalogging software has enabled us to measure intake air temperature under varied driving conditions.
Around town, testing has shown an average drop of around 10 degrees C which is good for around 3 percent power increase. Remember though that 3 percent power increase is difficult to feel. You'd feel a greater change in performance getting rid of that passenger. In certain conditions a 30° C drop has been measured.

We have these Hondata Gaskets (in bold) in stock pm me to order.

Honda/Acura

* B16A/B18C5
* D16 (92-2000 SOHC)
* B18C
* B18A/B18B
* H22A
* F22-VTEC
* ZC/D16A1(DOHC)
* K20A2, K20A, K20A3, K20Z1 (RSX, 02-05 Civic SI, CRV))
* K20Z3, K24A2 (TSX, Accord, Element, 06-07 Civic SI)
* S2000

Toyota Celica GT-S and Matrix

Mitsubishi 90-94 & 95-99 Eclipse turbo, and Lancer Evo

Nissan 350Z & G35, Sentra SER Spec-V, SR20DET (high port)

Hyundai Tiburon V6 and I4

Mazda 90-93 Miata 1.6L, 94-97 Miata 1.8L, 99-up Miata 1.8L

Subaru WRX

Dodge SRT4, 95-00 Neon 2.0L and 2.4L

Thermalnator

Thermalnator is a unique high temperature shielding gasket which replaces the stock intake manifold gasket. Thermalnator’s cooling properties reduce heat by stopping metal to metal contact between the intake manifold and the engine block. By using a Thermalnator gasket, you will reduce the heat of the air entering your engine, making up to 5% more power. Thermalnator gaskets allow the intake manifold to perform like an intercooler. Because the manifold is no longer heated by the cylinder head, the heat from incoming air can dissipate through the aluminum very rapidly. The basic formula for this is for every 5 degrees F increase in intake air temp, air density is reduced by 1%. The denser the air is, the better the gain in horsepower. Average testing has shown an 11 degrees F drop and up to 35 degrees in some applications. This is why a Thermalnator gasket is an excellent upgrade for your vehicle if it’s stock or modified.

What they make: Pm for pricing.

Honda / Acura
1999-2000 Civic Si (B16A2)
2002-2007 Civic Si
2000-2006 S2000 (F20/22C)
2002-2006 RSX JDM Base, Type S and Type R (K20A/A2/Z)
2002-2006 CRV LX/EX/SE 2/4WD (B20)
1992-1993 Integra GSR (B18C1)
1994-1997 Del Sol DOHC (B16A2)
2000-2001 Integra Type R (B18C5)
1994-2001 Acura Integra GSR (B18C1)
93-96 Prelude VTEC (H22A)
97-01 Prelude ALL (H22A)
2004-2006 TSX (K24A)
2003-2007 Accord 4 Cyl.
2003-2007 Element 4 Cyl.
1990-2001 Integra LS/GS/RS (B18A/B)
1998-2001 CRV LX/EX/SE

Nissan / Infiniti

S13 SR20DET
S14 SR20DET
RB20DET
RB25DET
RB26DETT
1991-1994 240SX (KA24)
1991-1996 Infiniti G20
1999-2002 Infiniti G20
1998-2001 Nissan Sentra SE
1991-1994 Nissan Sentra SE-R
1995-1998 Nissan 200 SX SE-R
2003-2006 G35
2003-2006 FX35
2002-2004 I35
2006-2007 M35
2003-2006 350Z
2002-2006 Altima
2002-2007 Maxima
2003-2007 Murano
2005-2006 Pathfinder
2004-2007 Quest
2005-2006 Xterra
2005-2006 Frontier

Subaru

04-06 Baja 2.5 Turbo
04-06 Forester Turbo
02-06 Impreza WRX
04-06 Impreza STi

Toyota

1993-1998 Supra Turbo
00-05 Celica GTS
05-06 Corolla XRS
02-06 Matrix XRS 2WD

Mitsubishi

90-98 Talon TSI Turbo
95-98 Talon TSI Turbo AWD
95-99 Eclipse Turbo
94 Galant 2.4 DOHC

VW / Audi

VW
98-05 VW Bettle 4CYL (AEG,AZG,AVH,BEH) 2.0L
95-02 VW Cabrio (ABA) 2.0L
93-06 VW Golf GL/GLS (ABA) 2.0L
93-00 VW Golf GTI (ABA,AEG) 2.0L
93-05 VW Jetta GL/GLS (ABA,ABA) 2.0L
01-05 VW JETTA Wagon (AZG,AVH,BEV) 2.0L
95-96 VW Passat GL (ABA) 2.0L

98-99 Passat 1.8T - Large Port
1.8T - Small Port

AUDI
00-02 Audi S4 2.7L
00-04 Audi A6 Quattro Turbo 2.7L
01-05 Audi Allroad Quattro 2.7L

97-00 Audi A4 1.8T

Mazda

1990-1993 Miata 1.6
1994-2005 Miata 1.8
1995-2000 Protege ES
1990-1994 Protege LX
1990-1991 AWD Protege

Porsche

87-88 924S
83-89 944 - All - except 87-89 944S/S2

Apex I Phenolic Gasket

The Gizzmo thermal gasket acts as a barrier, stopping heat transfer from the engine block to the intake manifold. Stopping this heat transfer results in a cooler intake temperature charge. A cooler intake air temperature increases engine power much the same way an intercooler does, however the thermal intake manifold gaskets can benefit both turbo and non-turbo vehicles.
The Gizzmo thermal gasket is made of hard, dense material by applying heat and pressure to layers of paper and glass cloth impregnated with synthetic resin. These layers are laminations of cellulose paper, cotton fabrics, synthetic yarn, glass fabrics, and unwoven fabrics.
When heat and pressure are applied to the layers, a chemical reaction (polymerization) transforms the layers into a high-pressure thermosetting industrial laminated plastic.

CONCEPT:
Thermal intake manifold gasket prevents heat soak from transferring from the engine block to the intake manifold, resulting in a cooler intake charge.

CHARACTERISTICS:
* More power and torque * Better throttle response * Improved fuel economy

Cars they are offered for: PM for pricing

Honda B16A
Honda B18C
Honda F20
Honda H22A
Honda/Acura K20A
Nissan S13 SR20
Nissan S14/15 SR20
Nissan RB26
Nissan RB25
Nissan VQ35
Mazda 13B S4 & S5
Mazda 13B S6 & S7
Mitsubishi 4G63
Subaru EJ25
Subaru EJ20
Toyota 2JZ-GTE
Toyota 3S-GTE

Dave · 07-11-2007, 04:26 PM

wheres the love for c30a?

S.Milone · 07-11-2007, 04:44 PM

For the NSX? I can have anything made needed threw Thermalnator.

Im2Slow · 07-11-2007, 05:37 PM

im pretty sure the c30a was found in the nsx. it was a 3liter

S.Milone · 07-11-2007, 07:48 PM

Would make sence he owns one. I'll look into it.

S.Milone · 07-23-2007, 06:06 PM

Turns out they can be made, only issue is you have to get 5 made at least not just one. So if anyone else is interested in these we can figure something out.

**TROLL** · 08-06-2007, 06:58 PM

hmmm... just posted in your other hondata thread but now i see like 12 options here... let me know whats available for the 07 STi motor and differences between all of these choices and why I want what please... and thanks.

S.Milone · 08-10-2007, 05:05 PM

PM SENt........

gsrboi80 · 08-11-2007, 09:47 AM

I have the Hondata piece on my EVO. Bump for a good product and vendor

IMPREZvWRX · 08-11-2007, 10:57 AM

Quote:

Originally Posted by TROLL

hmmm... just posted in your other hondata thread but now i see like 12 options here... let me know whats available for the 07 STi motor and differences between all of these choices and why I want what please... and thanks.

I'd like that info too, but for EJ207.

S.Milone · 08-13-2007, 02:30 PM

IMPREZvWRX pm sent

S.Milone · 08-13-2007, 02:30 PM

gsrboi80 Thank you for the feedback

S.Milone · 08-14-2007, 03:51 PM

Wrx Hondata Gaskets now in stock

**TROLL** · 08-14-2007, 04:13 PM

ordering mine now... i'd definitely recommend that anyone taking their intake manifold off use these gaskets as a replacement instead of purchasing oem ones again.

S.Milone · 08-14-2007, 06:26 PM

Thank you Troll

S.Milone · 08-20-2007, 03:56 PM

We just got more wrx and honda ones in stock.

S.Milone · 08-27-2007, 06:27 PM

The DynaPack Dyno Sheet below is a before and after
test of the Thermalnator Intake Manifold Gasket done on a B16A2 motor.

Below are some pictures of a used Thermalnator intake manifold gasket.

The gasket was pulled off of a 497 HP turbo charged S2000. This engine produces an extreme amount of heat and as you can see by the pictures below, the gasket has held up to the test. This gasket has been used for 60,000 Miles and has countless hours of street/track use on it. This engine is getting upgraded and the gasket will be reused in the next engine set up.

There was no melting or deformation of the gasket, unlike the competition's gasket.

S.Milone · 08-30-2007, 03:29 PM

Got some more in stock.

S.Milone · 09-05-2007, 04:21 PM

Thermalnators on in route. RB26, RB25, S14, S13, Ka24de

S.Milone · 09-07-2007, 06:05 PM

Rb26 Sold!!sold!!sold!!

07-11-2007, 04:15 PM	#1
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	The Govenator say Hondata Heatshields, Thermalnator, Apex-i Phenolic Gaskets Rule! Hondata Heatshields, Thermalnator, Apex I Phenolic gasket Even the Governator says it cools your intake air. Hondata Heat Shields The Heatshield is a replacement intake manifold gasket made from special high temperature plastic, designed to insulate the intake manifold from the cylinder head. Hondata have developed a special high temperature insulating gasket which replaces the stock intake gasket. This and bypassing several heat sources significantly reduces the transfer of heat from the head to the intake and incoming air giving you up to 5% more power. Turbocharged cars often use an aluminum intercooler to cool the air compressed by the turbo. The intake manifold is also made of aluminum but because it is heated by the head from combustion, works in reverse to an intercooler by heating the intake air by as much as 50° C. Fact: For every 3.3 °C (5° F) rise in intake temperature, air density drops 1%. The hotter the air, the less fuel the computer injects to compensate for reduced oxygen. HondaLogger datalogging software has enabled us to measure intake air temperature under varied driving conditions. Around town, testing has shown an average drop of around 10 degrees C which is good for around 3 percent power increase. Remember though that 3 percent power increase is difficult to feel. You'd feel a greater change in performance getting rid of that passenger. In certain conditions a 30° C drop has been measured. We have these Hondata Gaskets (in bold) in stock pm me to order. Honda/Acura * B16A/B18C5 * D16 (92-2000 SOHC) * B18C * B18A/B18B * H22A * F22-VTEC * ZC/D16A1(DOHC) * K20A2, K20A, K20A3, K20Z1 (RSX, 02-05 Civic SI, CRV)) * K20Z3, K24A2 (TSX, Accord, Element, 06-07 Civic SI) * S2000 Toyota Celica GT-S and Matrix Mitsubishi 90-94 & 95-99 Eclipse turbo, and Lancer Evo Nissan 350Z & G35, Sentra SER Spec-V, SR20DET (high port) Hyundai Tiburon V6 and I4 Mazda 90-93 Miata 1.6L, 94-97 Miata 1.8L, 99-up Miata 1.8L Subaru WRX Dodge SRT4, 95-00 Neon 2.0L and 2.4L Thermalnator Thermalnator is a unique high temperature shielding gasket which replaces the stock intake manifold gasket. Thermalnator’s cooling properties reduce heat by stopping metal to metal contact between the intake manifold and the engine block. By using a Thermalnator gasket, you will reduce the heat of the air entering your engine, making up to 5% more power. Thermalnator gaskets allow the intake manifold to perform like an intercooler. Because the manifold is no longer heated by the cylinder head, the heat from incoming air can dissipate through the aluminum very rapidly. The basic formula for this is for every 5 degrees F increase in intake air temp, air density is reduced by 1%. The denser the air is, the better the gain in horsepower. Average testing has shown an 11 degrees F drop and up to 35 degrees in some applications. This is why a Thermalnator gasket is an excellent upgrade for your vehicle if it’s stock or modified. What they make: Pm for pricing. Honda / Acura 1999-2000 Civic Si (B16A2) 2002-2007 Civic Si 2000-2006 S2000 (F20/22C) 2002-2006 RSX JDM Base, Type S and Type R (K20A/A2/Z) 2002-2006 CRV LX/EX/SE 2/4WD (B20) 1992-1993 Integra GSR (B18C1) 1994-1997 Del Sol DOHC (B16A2) 2000-2001 Integra Type R (B18C5) 1994-2001 Acura Integra GSR (B18C1) 93-96 Prelude VTEC (H22A) 97-01 Prelude ALL (H22A) 2004-2006 TSX (K24A) 2003-2007 Accord 4 Cyl. 2003-2007 Element 4 Cyl. 1990-2001 Integra LS/GS/RS (B18A/B) 1998-2001 CRV LX/EX/SE Nissan / Infiniti S13 SR20DET S14 SR20DET RB20DET RB25DET RB26DETT 1991-1994 240SX (KA24) 1991-1996 Infiniti G20 1999-2002 Infiniti G20 1998-2001 Nissan Sentra SE 1991-1994 Nissan Sentra SE-R 1995-1998 Nissan 200 SX SE-R 2003-2006 G35 2003-2006 FX35 2002-2004 I35 2006-2007 M35 2003-2006 350Z 2002-2006 Altima 2002-2007 Maxima 2003-2007 Murano 2005-2006 Pathfinder 2004-2007 Quest 2005-2006 Xterra 2005-2006 Frontier Subaru 04-06 Baja 2.5 Turbo 04-06 Forester Turbo 02-06 Impreza WRX 04-06 Impreza STi Toyota 1993-1998 Supra Turbo 00-05 Celica GTS 05-06 Corolla XRS 02-06 Matrix XRS 2WD Mitsubishi 90-98 Talon TSI Turbo 95-98 Talon TSI Turbo AWD 95-99 Eclipse Turbo 94 Galant 2.4 DOHC VW / Audi VW 98-05 VW Bettle 4CYL (AEG,AZG,AVH,BEH) 2.0L 95-02 VW Cabrio (ABA) 2.0L 93-06 VW Golf GL/GLS (ABA) 2.0L 93-00 VW Golf GTI (ABA,AEG) 2.0L 93-05 VW Jetta GL/GLS (ABA,ABA) 2.0L 01-05 VW JETTA Wagon (AZG,AVH,BEV) 2.0L 95-96 VW Passat GL (ABA) 2.0L 98-99 Passat 1.8T - Large Port 1.8T - Small Port AUDI 00-02 Audi S4 2.7L 00-04 Audi A6 Quattro Turbo 2.7L 01-05 Audi Allroad Quattro 2.7L 97-00 Audi A4 1.8T Mazda 1990-1993 Miata 1.6 1994-2005 Miata 1.8 1995-2000 Protege ES 1990-1994 Protege LX 1990-1991 AWD Protege Porsche 87-88 924S 83-89 944 - All - except 87-89 944S/S2 Apex I Phenolic Gasket The Gizzmo thermal gasket acts as a barrier, stopping heat transfer from the engine block to the intake manifold. Stopping this heat transfer results in a cooler intake temperature charge. A cooler intake air temperature increases engine power much the same way an intercooler does, however the thermal intake manifold gaskets can benefit both turbo and non-turbo vehicles. The Gizzmo thermal gasket is made of hard, dense material by applying heat and pressure to layers of paper and glass cloth impregnated with synthetic resin. These layers are laminations of cellulose paper, cotton fabrics, synthetic yarn, glass fabrics, and unwoven fabrics. When heat and pressure are applied to the layers, a chemical reaction (polymerization) transforms the layers into a high-pressure thermosetting industrial laminated plastic. CONCEPT: Thermal intake manifold gasket prevents heat soak from transferring from the engine block to the intake manifold, resulting in a cooler intake charge. CHARACTERISTICS: * More power and torque * Better throttle response * Improved fuel economy Cars they are offered for: PM for pricing Honda B16A Honda B18C Honda F20 Honda H22A Honda/Acura K20A Nissan S13 SR20 Nissan S14/15 SR20 Nissan RB26 Nissan RB25 Nissan VQ35 Mazda 13B S4 & S5 Mazda 13B S6 & S7 Mitsubishi 4G63 Subaru EJ25 Subaru EJ20 Toyota 2JZ-GTE Toyota 3S-GTE __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Last edited by S.Milone; 08-31-2007 at 04:36 PM.

07-11-2007, 04:44 PM	#3
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	For the NSX? I can have anything made needed threw Thermalnator. __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Last edited by S.Milone; 07-23-2007 at 04:58 PM.

07-11-2007, 07:48 PM	#5
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	Would make sence he owns one. I'll look into it. __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

07-23-2007, 06:06 PM	#6
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	Turns out they can be made, only issue is you have to get 5 made at least not just one. So if anyone else is interested in these we can figure something out. __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

08-10-2007, 05:05 PM	#8
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	PM SENt........ __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

07-11-2007, 04:26 PM	#2
Dave Tri-State Post Whore Join Date: Jul 2005 Location: Cherry hill, NJ Member #633 My Ride: Shelby Z, ZJ, NSX, CBR954RR, Hawk GT iTrader: (0)	wheres the love for c30a?

07-11-2007, 05:37 PM	#4
Im2Slow Tri-State Addict Join Date: Apr 2007 Member #4567 iTrader: (0)	im pretty sure the c30a was found in the nsx. it was a 3liter

08-11-2007, 09:47 AM	#9
gsrboi80 Tri-State Addict Join Date: Oct 2006 Member #2795 My Ride: Evolution Baby iTrader: (0)	I have the Hondata piece on my EVO. Bump for a good product and vendor

08-13-2007, 02:30 PM	#11
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	IMPREZvWRX pm sent __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

08-13-2007, 02:30 PM	#12
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	gsrboi80 Thank you for the feedback __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

08-14-2007, 03:51 PM	#13
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	Wrx Hondata Gaskets now in stock __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

08-14-2007, 06:26 PM	#15
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	Thank you Troll __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

08-20-2007, 03:56 PM	#16
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	We just got more wrx and honda ones in stock. __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

08-27-2007, 06:27 PM	#17
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	The DynaPack Dyno Sheet below is a before and after test of the Thermalnator Intake Manifold Gasket done on a B16A2 motor. Below are some pictures of a used Thermalnator intake manifold gasket. The gasket was pulled off of a 497 HP turbo charged S2000. This engine produces an extreme amount of heat and as you can see by the pictures below, the gasket has held up to the test. This gasket has been used for 60,000 Miles and has countless hours of street/track use on it. This engine is getting upgraded and the gasket will be reused in the next engine set up. There was no melting or deformation of the gasket, unlike the competition's gasket. __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Last edited by S.Milone; 08-28-2007 at 04:17 PM.

08-30-2007, 03:29 PM	#18
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	Got some more in stock. __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

09-05-2007, 04:21 PM	#19
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	Thermalnators on in route. RB26, RB25, S14, S13, Ka24de __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

09-07-2007, 06:05 PM	#20
S.Milone Tri-State Post Whore Join Date: Dec 2006 Location: PA Member #3073 My Ride: 240sx hatch iTrader: (0)	Rb26 Sold!!sold!!sold!! __________________ East Coast Drift Club's - Come and see To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Great Parts To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Old Farts Rule!!!!!!	BlkWhtTSI	Gallery	12	01-15-2011 05:41 AM
the govenator cuming	04 Turbo Spec	Gallery	6	10-26-2006 03:27 PM
Ray and Scott Rule!	turbotool	General Car Related Chat	1	07-12-2005 10:45 PM