Need a quote - TriStateTuners.com :: Home of Tristate Auto Enthusiast

OutToWinPAHC · 08-07-2009, 12:28 AM

I am going to pull my calipers next week and drop them off for powder. You allready quoted me for these. But I was wondering if you could also quote me to sand or bead blast my headers. Stadard length LS1 headers for my S13. Could you also quote to blast and powder coat them? I want to avoid ceramic coating, they will be wrapped after paint or powder.

LPC · 08-07-2009, 11:18 AM

Powder Coating wont hold up to the heat of headers

ceramic or jethot is the only coatings that will withstand the heat the powder coat will just bubble and flake off.

OutToWinPAHC · 08-07-2009, 03:13 PM

Price to coat these puppies then? I was planning on wrapping them because I heard of ceramic coating causing causing 02 code problems.

They are mustang 302 short tube headers drilled to work with the LS1, the left side was modified to work in the S-Chassis. So the total coat will be for 1 pair of short tube headers (gloss finish coated), and for 1 pair of 300ZX Z32 Iron calipers coated red.

I'm a cash guy only, and will be able to drop them off next week sometime.

OutToWinPAHC · 08-09-2009, 05:27 PM

After speaking on the phone I pulled the headers. I need to order the bungs so it may take a few extra days so the week after possibly. I also didn't like the weldes, so I am going to get those fixed by my buddy first.

I may add something to my list. My intake tube is steel, polished stainless I think. 4 inch diameter and about 15 inch long. I was going to wrap it but I am going for clean on this car. How much to ceramic coat that too? Same color as the headers.

OutToWinPAHC · 08-27-2009, 11:15 PM

Hey they are finally done! There was an issue with the welds ont he one header so my friend had to break them down and rebuild them. I am dropping them off tomorrow along with my intake tube for ceramic.

LPC · 08-28-2009, 12:05 AM

Hi There and i shall see you tomorrow

and guess what if you come tomorrow i will give you a sneak peak at what we have inline for the fall season

08-07-2009, 12:28 AM	#1
OutToWinPAHC Tri-State Post Whore Join Date: Jun 2007 Location: Tokelau Member #5081 My Ride: R33 GTS25T, RHD E46, Truck, part R32 GTR iTrader: (2)	Need a quote I am going to pull my calipers next week and drop them off for powder. You allready quoted me for these. But I was wondering if you could also quote me to sand or bead blast my headers. Stadard length LS1 headers for my S13. Could you also quote to blast and powder coat them? I want to avoid ceramic coating, they will be wrapped after paint or powder.

08-28-2009, 12:05 AM	#6
LPC Former Vendor Join Date: Aug 2007 Location: Yardley PA Member #5666 My Ride: 92 Eagle Talon TSI iTrader: (0)	Hi There and i shall see you tomorrow and guess what if you come tomorrow i will give you a sneak peak at what we have inline for the fall season Last edited by LPC; 08-28-2009 at 12:08 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
quote	92sileighty	Bonehead Performance	2	12-30-2009 03:14 PM
ms6 quote	superskaterxes	(Past Vendors)	11	04-27-2009 08:33 AM
Quote	WRX_JB	(Past Vendors)	5	04-15-2009 02:26 AM
quote please	RedDawg	(Past Vendors)	0	04-14-2009 12:03 PM
Quote	dave2610	(Past Vendors)	1	04-02-2009 06:40 PM

08-07-2009, 11:18 AM	#2
LPC Former Vendor Join Date: Aug 2007 Location: Yardley PA Member #5666 My Ride: 92 Eagle Talon TSI iTrader: (0)	Powder Coating wont hold up to the heat of headers ceramic or jethot is the only coatings that will withstand the heat the powder coat will just bubble and flake off.

08-07-2009, 03:13 PM	#3
OutToWinPAHC Tri-State Post Whore Join Date: Jun 2007 Location: Tokelau Member #5081 My Ride: R33 GTS25T, RHD E46, Truck, part R32 GTR iTrader: (2)	Price to coat these puppies then? I was planning on wrapping them because I heard of ceramic coating causing causing 02 code problems. They are mustang 302 short tube headers drilled to work with the LS1, the left side was modified to work in the S-Chassis. So the total coat will be for 1 pair of short tube headers (gloss finish coated), and for 1 pair of 300ZX Z32 Iron calipers coated red. I'm a cash guy only, and will be able to drop them off next week sometime.

08-09-2009, 05:27 PM	#4
OutToWinPAHC Tri-State Post Whore Join Date: Jun 2007 Location: Tokelau Member #5081 My Ride: R33 GTS25T, RHD E46, Truck, part R32 GTR iTrader: (2)	After speaking on the phone I pulled the headers. I need to order the bungs so it may take a few extra days so the week after possibly. I also didn't like the weldes, so I am going to get those fixed by my buddy first. I may add something to my list. My intake tube is steel, polished stainless I think. 4 inch diameter and about 15 inch long. I was going to wrap it but I am going for clean on this car. How much to ceramic coat that too? Same color as the headers.

08-27-2009, 11:15 PM	#5
OutToWinPAHC Tri-State Post Whore Join Date: Jun 2007 Location: Tokelau Member #5081 My Ride: R33 GTS25T, RHD E46, Truck, part R32 GTR iTrader: (2)	Hey they are finally done! There was an issue with the welds ont he one header so my friend had to break them down and rebuild them. I am dropping them off tomorrow along with my intake tube for ceramic.