Cast Magnus Intake Manifolds in-stock at Extreme PSI - TriStateTuners.com :: Home of Tristate Auto Enthusiast

extremepsi · 07-17-2017, 05:57 PM

Cast Magnus Intake Manifolds in-stock at Extreme PSI

Click here to shop!

The Design & The Results

Cast in A356 Aluminum with a wall thickness of 3/16"; the Plenum shape features a varying contoured tapered profile at a volume of 5 liters. The runners themselves are completely revolutionary in their design; featuring an integrated velocity stack that gradually transitions into the head port profile. It was designed entirely against the shape of the original cylinder head port taking advantage the 10° port entry of the EVO head maintaining un-interrupted laminar flow. The Magnus Cast Intake Manifold will work with throttle bodies from stock right up to 100mm and have seen consistent gains from 30 awHp to 52 awHp with varying setups. Transient boost response is exceptional and it can bolt together in a stock location if required while still being able to be used on a full blown race application.

Features

2 years of research and development
Cast from A356-T6 Aluminum Alloy
High quality casting gives a superior surface finish
Enhanced flow dynamics utilizing CAD Modeling & CFD simulation
Flowbenched and dynamically tested
Dynotested proven up to 50 HP
Ability to flow 100 lb/min (1000 HP) of air at 60PSI while maintaining equal flow distribution
Can be installed in stock location with clearance for original battery (with adaptor)
Install kits are optional and can be purchased to include heat barrier gaskets, and adaptor plate to run stock throttle bodies (easily upgradeable). Remote map sensor boss is optional for use with factory ECU's
Stock turbo gains up to 40HP
15 degree entry to the throttle body facilitates intercooler plumbing
Can be configured for 8 injector setup.
Fits factory fuel rail or Magnus high flow fuel rails
5L plenum with contoured velocity stacks molded into the floor for huge top end and minimal turbulence
Magnus Quality and Lifetime warranty

Applications: EVO IV to IX

Finish: Cast aluminum finish
Color: Raw aluminum

Click here to shop!

07-17-2017, 05:57 PM	#1
extremepsi Vendor Join Date: Feb 2006 Location: Bensalem, PA Member #1500 iTrader: (0)	Cast Magnus Intake Manifolds in-stock at Extreme PSI *Cast Magnus Intake Manifolds in-stock at Extreme PSI* *Click here to shop!* The Design & The Results Cast in A356 Aluminum with a wall thickness of 3/16"; the Plenum shape features a varying contoured tapered profile at a volume of 5 liters. The runners themselves are completely revolutionary in their design; featuring an integrated velocity stack that gradually transitions into the head port profile. It was designed entirely against the shape of the original cylinder head port taking advantage the 10° port entry of the EVO head maintaining un-interrupted laminar flow. The Magnus Cast Intake Manifold will work with throttle bodies from stock right up to 100mm and have seen consistent gains from 30 awHp to 52 awHp with varying setups. Transient boost response is exceptional and it can bolt together in a stock location if required while still being able to be used on a full blown race application. Features 2 years of research and development Cast from A356-T6 Aluminum Alloy High quality casting gives a superior surface finish Enhanced flow dynamics utilizing CAD Modeling & CFD simulation Flowbenched and dynamically tested Dynotested proven up to 50 HP Ability to flow 100 lb/min (1000 HP) of air at 60PSI while maintaining equal flow distribution Can be installed in stock location with clearance for original battery (with adaptor) Install kits are optional and can be purchased to include heat barrier gaskets, and adaptor plate to run stock throttle bodies (easily upgradeable). Remote map sensor boss is optional for use with factory ECU's Stock turbo gains up to 40HP 15 degree entry to the throttle body facilitates intercooler plumbing Can be configured for 8 injector setup. Fits factory fuel rail or Magnus high flow fuel rails 5L plenum with contoured velocity stacks molded into the floor for huge top end and minimal turbulence Magnus Quality and Lifetime warranty Applications: EVO IV to IX Finish: Cast aluminum finish Color: Raw aluminum *Click here to shop!* __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. 215-244-4295

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New JMFab Race Intake Manifold IN STOCK at Extreme PSI	extremepsi	Extreme PSI	0	02-23-2017 09:59 PM
Need advice on intake manifolds	ndubz	Subaru Talk	64	01-07-2009 02:32 PM
Intake manifolds	Jp2slow	Subaru Talk	2	09-16-2007 11:18 PM