11-21-2006, 07:03 AM | #1 |
Tri-State Aficionado
|
Snow Performance Water Injection Stage kits
I have sourced together 3 different kits based on your individual needs / setup : Option 1 Stage 1 Water/methanol injection system with everything needed to start making big HP! Includes: 150 psi high volume pump, adjustable boost pressure switch, 2-qt. Reservoir, two nozzles sized to your FWHP and boost levels, Bosch relay, all the electrical parts, fittings, tubing etc. to install - a complete kit made with quality, proven components. Option 2 - Variable Stage 2 with Variable Controller Includes Stage-1 plus: 1. An upgraded 150psi pump for incredible atomization. 2. Variable Controller that varies the quantity injected vs. boost. This allows maximum power at all RPM/boost levels as just the right amount is injected at all times. Features include adjustments for onset boost level and full quantity boost level. (See Variable Controller in ?products? for a full list of benefits). Note: The variable controller replaces the boost pressure switch and relay included in the stage-1 kit. Option 2 - MAF Stage 2 with MAF Controller Includes Stage-1 plus: 1. An upgraded 150psi pump for incredible atomization. 2. Snow Performance has developed a new Stage-2 Boost Cooler? water/methanol injection system that uses a new Mass Air Flow Variable Controller that varies the quantity injected with the amount of air going in the engine. Because the correct amount is injected at all times, power and drivability is much improved over the typical on-off systems. The MAF (mass air flow) Variable Controller represents the latest technology in Water/Methanol system control. It is especially applicable to positive displacement supercharged, fast spooling turbo, and naturally aspirated fuel injected applications. It increases the quantity injected based on the air flow of the engine (MAF). Designed for use with your stock 0-5 volts. Features include adjustments for onset MAF level and full quantity MAF level. (See MAF Variable Controller in ?products? for a full list of benefits) Note: The MAF variable controller replaces the boost pressure switch and relay included in the stage-1 kit. Option 3 - ( MAF or Variable ) Stage 2 with Safe Injection module ( choose your controller type ) I highly recommend this module. You can wire this into a boost controller and it can be set to limit your boost ( cut the power ) when activated. Can help you save your engine if you have tuned to a higher boost setting with the water injection spraying. For years, many have wanted to use water/methanol injection but have not taken advantage of the power increases do to safety concerns. Designed as an ad-on to the Boost Cooler? water/methanol injection system, Safe Injection? provides for a safe tune in those instances where no injection is present and an aggressive tune is utilized.? This system reduces boost or timing anytime injection quantity goes below a set point (e.g. if reservoir level goes too low) making the tune instantly conservative for the ultimate in safe water/methanol injection. Please inquire about other accessories from Snow Performance. Option 1 price - $250 Option 2 price ( MAF and MAP / Variable =the same price ) - $325 Option 3 price - $ 414 3 different nozzles come with the kit ( for SRT - 4 owners with turbo upgrades ) 175ml/min nozzle @ 100psi=200ml/min @ 200psi=240ml/min 375ml/min nozzle @ 100psi=430ml/min @ 200psi=520ml/min 625ml/minnozzle @ 100psi=720ml/min @ 200psi=865ml/min add $35 for shipping in the 48 states ( No extra charges for paypal / amex / mc / visa / discover ) Last edited by The Devils Z; 01-21-2007 at 06:32 PM. |
11-21-2006, 07:04 AM | #2 |
Tri-State Aficionado
|
ALL -
Complete Product line and MSRP Pricing Safe Injection Description: For years, many have wanted to use water/methanol injection but have not taken advantage of the power increases do to safety concerns. Designed as an ad-on to the Boost Cooler? water/methanol injection system, Safe Injection? provides for a safe tune in those instances where no injection is present and an aggressive tune is utilized.? This system reduces boost or timing anytime injection quantity goes below a set point (e.g. if reservoir level goes too low) making the tune instantly conservative for the ultimate in safe water/methanol injection. Operation The SI-10 and SI-05 monitor the flow of Water/Methanol in the system. When flow drops below 0.10 Gallons per Minute (GPM), equal to 378 ml/min,( 0.05 GPM or175ml/min on the SI-05) the fault trigger will go to a high state of 12 volts. In addition to the supplied red LED, this trigger can be used to signal the following: 1. an ignition/timing controller such as an MSD timing computer if using an MSD ignition 2. aftermarket engine computer 3. a solenoid such that boost is reduced in a wastegated turbo set-up. ( $39.95 list. See below.) 4. a solenoid to evacuate boost on a supercharged set-up. The trigger signal can deliver up to 1.5 amps to drive a solenoid or relay. Variable controller ~ comes with the stage 2 kit !! Description: The Electronic Variable Controller from Snow Performance represents the latest technology in Water/Methanol system control. The controller is designed to increase injection pressure over a user adjustable range and quickly shut off when boost pressure drops to prevent misfire. No special MAP or MAF is required. The controller has a .2 to 5 volt output signal (denotes 2.9 to 36.3 manifold boost psi) that can be used for an input to other applications. The small rugged design and easy setup makes the EVC the logical choice for automotive/offroad enthusiast. Operation: An external hose barb is provided to connect the controller to manifold pressure. The user then sets two dials that are located under the lid of the controller. The first dial tells the controller what pressure to turn on and off. The second dial tells the controller the pressure where maximum injection is required. Once the two dials are set, the controller will linearly increase/decrease the injection pressure over the set range. Start pressure is adjustable from .5 to 8psi. The Full pressure is adjustable from 2 to 25psi. Note that if the Full Psi dial is set below the Start Psi setting, full injection pressure will occur once the Start boost psi is reached Reverse Flow Check Valve Description: This valve mounted between the reservoir and the pump inlet is used to keep boost from reverting back through the reservoir during the pre-injection state. Recommended in high boost (over 15psig) applications. Fluid Level Switch Upgrade Description: Indicates low fluid level to insure you don't run out. Includes an upgraded reservoir with level switch, Red LED, and fittings necessary to install. Solenoid Upgrade Description: For use when the nozzle is mounted after the throttle plate (to keep from siphoning at idle) or if the nozzle must be mounted lower than the reservoir (to keep from gravity feeding). There are multiple nozzle setups based on power expectations (150, 175, 225, 375, and 625 ml/min.). 150-1500 HP applications. You can email me / PM / or call me for pricing and availability Last edited by The Devils Z; 01-20-2007 at 06:51 PM. |
11-21-2006, 07:04 AM | #3 |
Tri-State Aficionado
|
The Snow Performance sales pitch:
" 1) Engineering - each system has been designed and tested by engineers to ensure reliability and robustness. The Boost Cooler will do what it is designed to do for a very long time 2) Digital Variable Controllers for different applications - Not just boost actuated, we have specially designed controllers for each vehicle / application to ensure maximum power 3) High Pressure/ High Volume Pumps - Our pumps are specially designed for Snow Performance to deliver higher pressures and reliability. Each pump is pre-tested and designed to work with methanol. 4) Unsurpassed Atomization - Along with higher pressures, our nozzles are specially designed to spin the fluid supersonically before being forced through a venturi shaped oriface for the ultimate in atomization. 5) Trained technical and tuning advice - trained, knowledgeable technicians are always available to help. 6) Warranty - Life time warranty available. Snow backs it's systems with industry leading warranties. 7) Customer Service - Expert technical advice is available anytime during business hours. We have the experience to answer installation and tuning questions. 8) Safety - Our new safe injection is the ultimate in safety for even the most aggressively tuned applications. This ensures worry-free power in even the most demanding racing applications as well as full power on the street. With the proper tuning, expect about 10-20% improvement in power. Can be used in Nitros applications. Can be used in MAP and MAF applications. The Safe Injection Module can be used to trigger a warning lamp, bleed off boost pressure ( electronic boost controller or manual boost controller),or switch EMS maps." Email me / PM direct for special pricing and availability. |
12-11-2006, 11:37 AM | #5 |
Tri-State Addict
|
not for the wrx?
b/c i am going with the snow kit in the spring, so picking a kit up now for a good price would work...im just inquiring.
__________________
"Did that guy just say my car is made in Australia?!" To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Yeah, so my dad is in a HARDCORE band. he is cooler than me, be their myspace friend. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. |
12-11-2006, 12:18 PM | #6 |
Tri-State Aficionado
|
Wrx
|
04-27-2007, 09:33 AM | #11 |
Tri-State Aficionado
|
PSA - Product Enhancement Snow Performance
Snow Performance has designed a new Safe Injection module
Sales Pitch : "New Improved SafeInjection™uses a flow meter to indicate flow rate and now comes with an adjustable trigger flow level. Boost and timing reduction system for use with the Boost Cooler® water/methanol injection system provides for safety even with the most aggressive tunes. Designed as an add on to the Boost Cooler® water/methanol injection system, SafeInjection™ provides for a safe tune in those instances where no injection is present and an aggressive tune is utilized. This system reduces boost and/or timing anytime injection quantity goes below a set point regardless of the reason (ran out of fluid, clogged line, etc.). This sets your vehicle into a "safe mode" making your tune instantly conservative for the ultimate in safe water/methanol injection. " OK now the real PR: instead of a standard setting to detect flow rate, the new safe injection module has an adjustable setting which can be used to enhance tuning. adjustable knob / switch also, a warning lamp for when the safe injection is activated is now standard instead being available as an additional accessory / option. MSRP $apprx $140 range also , within weeks a 52 mm gauge that displays real time actual flow rate will be available ( price range $100 ). I will have pics available for that as well shortly. I have 2 water injection kits in stock with the "old style" safe injection. If interested in a new kit / unused for a good price - send me an email. |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Snow Performance Stage II Kits!!!! | injectionconnect | (Past Vendors) | 0 | 02-28-2009 11:43 AM |
Snow Performance Water/Meth Official Dealer | xenocron | (Past Vendors) | 0 | 12-01-2007 09:12 PM |
UCC Snow Performance Alcohol Injection GB | EVO8YOU | (Past Vendors) | 27 | 07-02-2006 07:24 PM |