OMG a dyno graph!!! - Page 8 - TriStateTuners.com :: Home of Tristate Auto Enthusiast

05GT · 09-01-2006, 06:26 PM

Quote:

Originally Posted by Demonicbird00

when you go to atco, obviously youll be running faster then a 11.5

so get used to launching the car and just running 1/8 times, for the most part what you run in the 1/8 is etched in stone what youll run in the 1/4.

then the last run of the day/nite let it loose and run the full 1/4. the repeat a week later

nice numbers on the stock block. what was you psi before blowing the motor?

-brandon

I was seeing 10psi on the stock motor.

That is one of the reasons the car is still in the shop, the douche bags that orginally did it, besides screwing up A LOT of things....I have huge rant here if you are interested in the whole story...
http://www.tristatetuners.com/forum/...ad.php?t=17469

But anyway, when it was done being built, with ported heads and cams, I should be seeing less boost, well instead I was seeing like 12-13lbs with the new setup, as oppose to the around 8psi I was expecting.

Demonicbird00 · 09-01-2006, 06:31 PM

gotcha.

what is the stock CR of the 05 stangs?

what is the CR gonna be w/ the new motor? is it a new stock block forged out or what?

-brandon

05GT · 09-01-2006, 07:16 PM

Quote:

Originally Posted by Demonicbird00

gotcha.

what is the stock CR of the 05 stangs?

what is the CR gonna be w/ the new motor? is it a new stock block forged out or what?

-brandon

Stock CR was 9:8.1
The new block is 8:4.1 Just a notch below the CR of the 03/04 cobras of 8:5.1

Umm...Its a 4.6L forged aluminum block with an 8bolt cobra crank.
Here is what the website says lol....its a SuperMOD....and here...

NEW Level 10 Race Prepped 4.6 Aluminum 05 GT block with PRO-X Forged pistons,1.5 1.5 3mm SS50 U Molly rings with Tri Metal bearings, 4340 Forged H-beam rods with ARP 2000 rod bolts, Forged steel 8 bolt crankshaft. Rotating assembly is balanced to Racing tolerances. Bearing clearances are set and the short block is Professionally assembled in our climate controlled clean room. Includes FREE upgrade to ARP main studs and D.S.S. Main support System.,

DocEwww · 09-01-2006, 07:23 PM

Quote:

Originally Posted by 05GT

Umm...Its a 4.6L forged aluminum block with an 8bolt cobra crank.

One thing you wish u knew before hand...ha

09-01-2006, 06:31 PM	#142
Demonicbird00 Tri-State Addict Join Date: Jul 2005 Location: south jersey Member #629 My Ride: 00 TA iTrader: (0)	gotcha. what is the stock CR of the 05 stangs? what is the CR gonna be w/ the new motor? is it a new stock block forged out or what? -brandon __________________ 00 Black T/A m6 Stock Internals 343hp/349tq 11.81@ 117 1.59 60' Cam Only 456hp/408tq 10.84 @ 127.8 1.56 60' To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How reliable is your laptop? Check out the graph!	lagos	Off-Topic	50	11-23-2009 10:19 PM
06 wrx dyno tuning results (graph will be up soon)	RayArroyo	(Past Vendors)	4	11-17-2008 01:25 PM
auk113's S14 Drift Slut (update 6/20/08 dyno graph added )	auk113	Member Journals	58	10-21-2008 11:25 AM
RT Tuning Dyno Event - April 14+15, cheap dyno pulls! It's for a good cause!!!!	95TurboDC2	Upcoming Events	180	04-22-2007 01:39 PM
dyno tuned graph	AMF Racing	Gallery	13	03-02-2007 11:10 AM