Turbo diesel build up

[poolmike]

I just got the heads back from Lorenzo's Fast Flow this week. The long block got assembled this morning and is ready for paint. I placed some of the olive drab coated accessories(courtesy of Bonehead) on the engine for pics.
This is the future grease burning heart for the Jeep.





While you all wheel drive folks were playin' in the snow this morning, I fired up ol' smokey to warm the garage with a little coal fire.

[teh DIRT]

p.i.m.p.

[S4toSTI]

lol 120 in the garage... Ps mike this winter we need to put the jeep in some of our snow vids.

[blkbomber01]

you took it to lorenzo huh.... how long did he take to get it back to you

[poolmike]

Originally Posted by blkbomber01

you took it to lorenzo huh.... how long did he take to get it back to you

2 weeks. I've known Lorenzo for years.....ya gotta bug the schlitz out of to get stuff done..... well worth the wait. Also, keep in mind there wasn't too much custom work involved.....

[99SL2_Modder]

WHERE ARE THE SPARK PLUG HOLES?!?!??

omg, it can't start without spark plugz0rz!




*note: I really am just kidding.*

[Gorilla Unit 33]

nice. when do u figure on having the thing back on the road?

[noreaga0221]

Compression ratio?

[poolmike]

Originally Posted by Gorilla Unit 33

nice. when do u figure on having the thing back on the road?

It's still runnin on the gas motor. As soon as the diesel is completely assembled, I will remove the whole front end of the truck for some MAJOR rust repair. With the front sheet metal removed I can easily install the new engine/trans combo. I am also trashing both front and rear axle assemblies for more modern axles out of a Chevy. Its going to take some time and a whole lot of $$$$.

As far as compression goes, stock was 22:1, the new pistons are 17.5:1. I plan on running ~15-18 psi That should get me in the 250 hp/700 ft.lb. range. I might get silly with some propane/water injection and maybe a little nos.

[WhiteFiveO]

hey what motor is that?? also what kind of jeep you plan on putting that thing in??

[blkbomber01]

Originally Posted by poolmike

2 weeks. I've known Lorenzo for years.....ya gotta bug the schlitz out of to get stuff done..... well worth the wait. Also, keep in mind there wasn't too much custom work involved.....

yeah... i sent a block up to him to get done and it took him about 3 months to get it back, and it wasnt like i asked him to a lot. but hey, maybe ill go with you next time so i can get it back a little sooner. im in the middle of doing a motor up for my vw and i didnt want to take it to him cause i want it to be in the car by spring time

[Gorilla Unit 33]

damn thats crazy

[poolmike]

Originally Posted by blkbomber01

yeah... i sent a block up to him to get done and it took him about 3 months to get it back, and it wasnt like i asked him to a lot. but hey, maybe ill go with you next time so i can get it back a little sooner. im in the middle of doing a motor up for my vw and i didnt want to take it to him cause i want it to be in the car by spring time

Well, it isn't just Lorenzo. My engine block/crank/rods were machined by Greg@ GN auto in Doylestown. Greg does some of the best machine work in Bucks County, but once again, I had to wait 3 months for it. Good machine shops are getting very tough to find and anyone with a good reputation will be extremely busy.

Don't be upset with Lorenzo, his crew does some great engine work. It is ALWAYS better to wait for good machine work rather than assemble an engine to find the crank cut too much or the cylinders bored too much....... done by a less than satisfactory machinist. I've seen it happen.

[D Money]

whats the motor going in?

[poolmike]

Originally Posted by subwrxkid

whats the motor going in?

A rusty old military Jeep.

[dolphinS4]

Looks like a great winter job Mike. Can't wait to see how it turns out.