Anarchy's S13 Coupe
 

Current Specs

Performance
- KA24DE-T
- FiveO 550cc injectors
- SR20DET MAF
- ISIS RS3871 Turbo
- Not Sure Turbo manifold
- Nismotronic engine management
- ISIS KA24DE FMIC Intercooler Kit
- ISIS Aluminum Radiator
- ISIS Aluminum Fan Shroud Kit
- ISIS low temp thermostat
- ISIS Single GT Exhaust
- ISIS Turbo Outlet
- ISIS 3" Downpipe
- ISIS SR20DET Suction Kit
- ISIS Exhaust Hangers
- Test Pipe

Interior
-AEM Uego Wideband
-Autometer Sport Comp Boost Gauge
-Autometer Sport Comp Oil Pressure Gauge
-Autometer Sport Comp Tach
-Autometer Sport Comp Speedo
-Autometer Sport Comp Fuel Level Gauge


Handling / Drivetrain
-BC type BR coilovers
-Wicked tuning tie rod ends
-Tension rods (not sure the brand, came with car)
-RUCAs (not sure the brand, came with car)
-ISIS solid rear subframe bushings
-Chassis stitch welded
-Welded Diff


Pretty stuff
- Circuit Sports Coolant Overflow Tank


--------Original Post---------
I would like to get some track time this year so I picked up a new toy that I'm hoping to have ready for ECB in two weeks.

Shell came with

-brand new Ksport coilovers
-tension rods
-wicked tuning tie rod ends
-aluminum rear subframe bushings. Not yet installed.
-some form of RUCAs
-a 10pt cage (not yet installed)
-an attempt at stitch welding
-lots of spray on bedliner in the engine bay :roll:
-possibly a dead body in the trunk because I haven't been able to open it quite yet

The way it sat as of Sat early aftertoon
http://tyler.xeroweb.com/s13coupe/coupe.jpg

http://tyler.xeroweb.com/s13coupe/coupe (4).jpg

Back at the garage
http://tyler.xeroweb.com/s13coupe/coupe (3).jpg

http://tyler.xeroweb.com/s13coupe/coupe (2).jpg

A few hrs later
http://tyler.xeroweb.com/s13coupe/coupe (1).jpg

Ksports and subframe removed
http://tyler.xeroweb.com/s13coupe/coupe (5).jpg

Stitch welding by previous owner
http://tyler.xeroweb.com/s13coupe/coupe (6).jpg

I put my GF to work... hehe
http://tyler.xeroweb.com/s13coupe/coupe (7).jpg

It's going to be a thrash fest for ECB!

Was this a shell on CL?

Yea it's going to be an awesome time! I just hope I can get the car finished so I can drive.

I didn't see it on Craigslist but it could have been

nice to see you back in an S-Chassis. See ya at ECB :mrgreen:

Thanks, they are addicting. This is now my 5th 240. Are you going to be bringing yours out?

sub'd to this one




i expect lots of updates if you are aiming for ECB!

Spray on bedliner removed
http://tyler.xeroweb.com/s13coupe/stripped.jpg

engine bay painted
http://tyler.xeroweb.com/s13coupe/paintedBay.jpg

Engine pulled from the nismaru. (Don't worry I'm not giving up on the project)
http://tyler.xeroweb.com/s13coupe/engineOut.jpg

Engine installed in s13 coupe.
http://tyler.xeroweb.com/s13coupe/engineIn.jpg

Swap Specs
SR20DET
Microtech LT10s Standalone
Microtech X4 Ignitor
Isis RS3371 Turbo
Greddy Profec B spec 2 boost controller
Exedy Stage 2 Clutch Kit
Isis lightweight pulleys
Isis oil pan
Isis short shifter
Isis turbo outlet
Isis air intake kit
Isis downpipe
SSQV bov
Nismo Thermostat

Parts needed to get the car on the road
Driveshaft
Trans harness
Radiator mounts
S13 Radiator (Anyone willing to trade for an Isis S14 radiator?)
Intercooler Pipe
Transmission mount
Test Pipe

do you need a 2 piece drive shaft? or are you looking for a single?

also might have the trans harness and mount

gotta look in the garage

Either or works for me

ohhhh Tyler..........haha

- Reinstalled brake lines/booster and master cyl
- hardwired lower trans harness (previous owner cut off plugs on body harness)
- Relocated battery to trunk
- Routed Microtech engine harness
- Removed heater core/blower/ everything not needed from under dash

http://tyler.xeroweb.com/s13coupe/062011 (1).jpg

Parts needed to get the car on the road
Driveshaft (picking up today after work)
Radiator mounts
S13 Radiator (Anyone willing to trade for an Isis S14 radiator?) If not I'll just make some upper mounts for now
Intercooler Pipe
Test Pipe

Monday I did the following

- Installed Axles
- Installed Welded Diff
- Installed Driveshaft
- Installed Trans mount

Last night did the following

- Connected fuel lines
- Fixed trunk latch
- Attempted to install clutch pedal but quickly found out someone who worked on the car previously drilled the hole for the master cyl about 1/2" from where it should be... wtf
- Wired the microtech, fuel pump, fans and coil packs in last night
- Started car :supz:

so you gonna make the cruise night Saturday?

Something weird was going on with the wiring so I ripped the entire wiring harness out and installed a painless performance fuse panel. As of right now it has working headlights, tail lights, turn signals, brake lights, reverse lights and ignition switch. All other chassis wires have been eliminated. Should hopefully see some track time in Englishtown, NJ this weekend. Sorry been too busy working on the car to take photos. Car moved out of garage under it's own power for the first time yesterday.

Well, a lot has changed since my last post. I pulled the SR and put it in my Sil-80 and then sold this shell to a buddy of mine. A few months later I sold the Sil-80 and I'm now buying this car back with a KA-T setup laying in the engine bay. Yes I mean laying in there not bolted in. Not 100% sure of the specs on the engine but the price was right and would like to see what she can do. Can't wait to get started, again.

Getting Ready to pull the KA out to look it over real good.
https://fbcdn-sphotos-a.akamaihd.net...24079050_n.jpg

Engine out. Looks like a brand new Exedy OEM Replacement clutch. I'll burn this one out and then throw in a SPEC Billet Flywheel and my Exedy Stage 2(SR20DET) I have laying around.
https://fbcdn-sphotos-a.akamaihd.net...17974176_n.jpg

Picked up an engine harness and ka24de ecu today. I will be tuning this car using Nismotronic. I'm choosing to go this route because 1. the manufacturer is pretty local to me and 2. there is tons of active development unlike Nistune which seems to have stopped progressing for some time. They should have Map based tuning on the stock ecu available sometime this summer.