12-22-2005, 08:17 PM | #1 |
Tri-State Addict
|
02-xx Nissan Sentra Spec-V: How-To Reset: SES, SRS, ABS Lights
I know there is already one for the engine code, but i think we need a place with all of them together. The following procedures apply to all vehicles with the QR25DE engine. Definately work in all SE-R's & Spec V's and maybe the 2.5L altimas. Mods.....please sticky this thread. thanks.
__________________
01 SE Granite SR20* Back to stock..... ........Just tryin to pay the damn thing off...... |
12-22-2005, 08:18 PM | #2 |
Tri-State Addict
|
SRS/Airbag Light
AIRBAG LIGHT RESET/DIAGNOSTIC PROCEDURE
From User Mode to Diagnosis Mode: Diagnosis mode activates only when a malfunction is detected, by turning the ingition switch as follows: 1. Turn ignition switch "ON". 2. After "AIR BAG" warning lamp lights for 7 seconds, turn ignition switch "OFF" within 1 second. 3. Wait more than 3 seconds. 4. Repeat steps 1 to 3 three times. 5. Turn ignition switch "ON". SRS will enter Diagnosis mode, if no malfunction is detected. From Diagnosis Mode to User Mode: After a malfunction is repaired, turn ignition switch "OFF" for at least one second, then back "ON". Diagnosis mode is returned to User Mode. If Switching Diagnosis mode to User mode is required while malfunction is being detected, turn ignition switch as follows: 1. Turn ignition switch "ON". 2. After "AIR BAG" warning lamp lights for 7 seconds, turn ignition switch "OFF" within one second. 3. Wait more than 3 seconds. 4. Repeat steps 1 to 3 three times. 5. Turn ignition switch "ON". **HOW TO ERASE SELF-DIAGNOSIS RESULTS** Without Consult-II: After a malfunction is repaired, switch the ignition "OFF" for at least one second, and then back "ON". Diagnosis mode returns to the User mode. At that time, the self-diagnostic result is cleared.
__________________
01 SE Granite SR20* Back to stock..... ........Just tryin to pay the damn thing off...... |
12-22-2005, 08:18 PM | #3 |
Tri-State Addict
|
SES/Check Engine Light
CHECK ENGINE LIGHT RESET/DIAGNOSTIC PROCEDURE
In car ECM Diagnostics/ECM Reset procedure: 1) Sit in the driver's seat. 2) Turn the ignition key to the ON position and wait three seconds. (Do not start the car.) 3) Fully depress and release the accelerator pedal five times in less than five seconds. 4) Wait exactly seven seconds. Fully depress the accelerator pedal for ten seconds until the MIL light flashes. 5) Release the accelerator pedal and start counting flashes to obtain the four-digit trouble code. Long flashes (0.6 seconds) indicate the first digit of the code; count the blinks one through nine and write down the first digit. (Ten blinks indicates a zero.) The next three digits follow in turn in the same fashion except with faster blinks (0.3 second) and a 1.0-second pause between digits. The ECM code repeats itself until you turn the ignition key to the OFF position, at which point the ECM resets itself to standard get-in-and-drive-the-car mode. You can look up the trouble codes in the ESM/FSM; there's a bunch of them. In the ESM, refer to page EC-639. Additionally, if you get four blinks of ten (0000), the ECM is indicating no malfunction. Clearing You can clear the code (and the annoying MIL) by holding down the accelerator pedal for more than 10 seconds while in Diagnostic Test Mode II. When you release the pedal, the ECM erases the trouble code(s). Check engine Codes REASON...................................CODE A/T 1ST GR FNCTN....................................0731 A/T 2ND GR FNCTN...................................0732 A/T 3RD GR FNCTN...................................0733 A/T 4TH GR FNCTN...................................0734 A/T TCC S/V FNCTN..................................0744 APP SEN 1/CIRC +5.................................0227 APP SEN 1/CIRC +5.................................0228 APP SEN 2/CIRC +5.................................1227 APP SENSOR +5.......................................1228 ASCD BRAKE SW......................................1572 ASCD SW. ................................................15 64 ASCD VHL SPD SEN..................................1574 ATF TEMP SEN/CIRC.................................0710 BRAKE SW/CIRCUT...................................1805 CAN COMM CIRCUIT ................................1000 CAN COMM CIRCUIT.................................1001 CKP SEN/CIRCUIT.....................................0335 CLOSED LOOP-B1....................................1148 CMP SEN/CIRC-B1....................................0340 CTP LEARNING.........................................1 225 CTP LEARNING.........................................1 226 CYL 1 MISFIRE.........................................03 01 CYL 2 MISFIRE.........................................03 02 CYL 3 MISFIRE.........................................03 03 CYL 4 MISFIRE.........................................03 04 ECM............................................... ..........0605 ECM BACK UP CIRCUIT............................1065 ECT SEN/CIRCUIT.....................................0117 ECT SEN/CIRCUIT....................................0118 ECT SENSOR............................................ 0125 ENG OVER TEMP.......................................0217 ENG OVER TEMP.......................................1217 ENGINE SPEED SIG...................................0725 ETC ACTR.............................................. ...1121 ETC FUNTION CIRC..................................1122 ETC MOT............................................... ...1128 ETC MOT PWR...........................................1124 ETC MOT PWR...........................................1126 EVAP GROSS LEAK....................................0455 EVAP PURG FLOW/MON............................0441 EVAP SMALL LEAK....................................0442 EVAP SYS PRES SEN.................................0452 EVAP SYS PRES SEN.................................0453 EVAP VERY SML LEAK...............................0456 EVAP VERY SML LEAK...............................1456 FTT SEN/CIRCUIT.....................................0182 FTT SEN/CIRCUIT.....................................0183 FTT SENSOR............................................ .0181 FUEL LEVEL SEN SLOSH...........................0460 FUEL LEVEL SEN/CIRC.............................1464 FUEL LEVEL SENSOR................................0461 FEUL LEVEL SEN/CIRC.............................0462 FUEL LEVEL SEN/CIRC.............................0463 FUEL SYS-LEAN-B1...................................0171 FUEL SYS-RICH-B1...................................0172 H02S1(B1)......................................... ......0132 H02S1(B1)......................................... ......0133 H02S1(B1)......................................... ......0134 H02S1(B1)......................................... ......1143 H02S1(B1)......................................... ......1144 H02S1 HTR (B1).......................................0031 H02S1 HTR (B1).......................................0032 H02S2(B1)......................................... ......0138 H02S2(B1)......................................... ......0139 H02S2(B1)......................................... ......1146 H02S2(B1)......................................... ......1147 H02S2 HTR (B1).......................................0037 H02S2 HTR (B1).......................................0038 IAT SEN/CIRCUIT.....................................0112 IAT SEN/CIRCUIT.....................................0113 IAT SENSOR............................................ .0127 INT/V TIM CONT-B1..................................0011 INT/V TIM CONT-B1..................................1111 ISC SYSTEM............................................ .0506 ISC SYSTEM............................................ .0507 KNOCK SEN/CIRC-B1...............................0327 KNOCK SEN/CIRC-B1...............................0328 L/PRESS SOL/CIRC..................................0745 MAF SEN/CIRCUIT....................................0101 MAF SEN/CIRCUIT....................................0102 MAF SEN/CIRCUIT....................................0103 MAF SENSOR...........................................1 102 MIL/CIRC.............................................. ...0650 MULTI CYL MISFIRE..................................0300 NO DTC DETECTED/FURTHER TEST..........FLASHING NO DTC (NO TROUBLE CODE)..................0000 O/R CLUTCH SOL/CIRC............................1760 P-N POS SW/CIRCUIT...............................1706 PNP SW/CIRC..........................................0705 PURG VOLUME CONT/V............................0444 PURG VOLUME CONT/V.............................0445 PURG VOLUME CONT/V.............................1444 SENSOR POWER/CIRC..............................1229 SFT SOL A/CIRC........................................0750 SFT SOL B/CIRC........................................0755 TCC SOLENOID/CIRC................................0740 THERMSTAT FNCTN...................................0128 TP SEN 1/CIRC.........................................0222 TP SEN 1/CIRC..........................................0223 TP SEN 2/CIRC.........................................1223 TP SEN 2/CIRC.........................................1224 TP SENSOR............................................ ...0221 TPV SEN/CIRC A/T....................................1705 TW CATALYST SYS-B1...............................0420 VC CUT/V BYPASS/V .................................1491 VC/V BYPASS/V.........................................1490 VEH SPD SEN/CIR AT................................0720 VEH SPEED SEN/CIRC..............................0500 VENT CONTROL VALVE..............................0447 VENT CONTROL VALVE..............................1446 VENT CONTROL VALVE..............................1448
__________________
01 SE Granite SR20* Back to stock..... ........Just tryin to pay the damn thing off...... |
12-22-2005, 08:19 PM | #4 |
Tri-State Addict
|
ABS Light
ABS LIGHT RESET/DIAGNOSTIC PROCEDURE
When a problem occurs in the ABS, the warning lamp on the instrument panel comes on. To start the selfdiagnostic results mode, ground the self-diagnostic (check) terminal located on Data Link Connector. The location of the malfunction is indicated by the warning lamp flashing. SELF-DIAGNOSIS PROCEDURE 1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2. Turn ignition switch OFF. 3. Ground terminal 9 of Data Link Connector with a suitable harness. 4. Turn ignition switch ON while grounding terminal 9. Do not depress brake pedal. 5. After 3.0 seconds, the warning lamp starts flashing to indicate the malfunction code No. (See NOTE.) 6. Verify the location of the malfunction with the malfunction code chart. Then make the necessary repairs following the diagnostic procedures. 7. After the malfunctions are repaired, erase the malfunction codes stored in the control unit. See Below 8. Rerun the self-diagnostic results mode to verify that the malfunction codes have been erased. 9. Disconnect the check terminal from the ground. The self-diagnostic results mode is now complete. 10. Check warning lamp for deactivation after driving vehicle over 30 km/h (19 MPH) for at least one minute. 11. After making certain that warning lamp does not come on, test the ABS in a safe area to verify that it functions properly. NOTE: The indication terminates after 5 minutes. However, when the ignition switch is turned from OFF to ON, the indication starts flashing again. HOW TO READ SELF-DIAGNOSTIC RESULTS (MALFUNCTION CODES) 1. Determine the code No. by counting the number of times the warning lamp flashes on and off. 2. When several malfunctions occur at one time, up to three code numbers can be stored; the latest malfunction will be indicated first. 3. The indication begins with the start code 12. After that a maximum of three code numbers appear in the order of the latest one first. The indication then returns to the start code 12 to repeat (the indication will stay on for five minutes at most). HOW TO ERASE SELF-DIAGNOSTIC RESULTS (MALFUNCTION CODES) 1. Disconnect the check terminal from ground (ABS warning lamp will stay lit). 2. Within 12.5 seconds, ground the check terminal three times. Each terminal ground must last more than 1 second. The ABS warning lamp goes out after the erase operation has been completed. 3. Perform self-diagnosis again. Only the start code should appear, no malfunction codes. ABS CODES Code No. Malfunctioning Part Reference Page 12 Self-diagnosis could not detect any malfunctions. 45 Actuator front left outlet solenoid valve 46 Actuator front left inlet solenoid valve 41 Actuator front right outlet solenoid valve 42 Actuator front right inlet solenoid valve 51 Actuator rear right outlet solenoid valve 52 Actuator rear right inlet solenoid valve 55 Actuator rear left outlet solenoid valve 56 Actuator rear left inlet solenoid valve 25 *1 Front left sensor (open-circuit) 26 *1 Front left sensor (short-circuit) 21 *1 Front right sensor (open-circuit) 22 *1 Front right sensor (short-circuit) 31 *1 Rear right sensor (open-circuit) 32 *1 Rear right sensor (short-circuit) 35 *1 Rear left sensor (open-circuit) 36 *1 Rear left sensor (short-circuit) 18 *1 Sensor rotor 61 *3 Actuator motor or motor relay 63 Solenoid valve relay 57 *2 Power supply (Low voltage) 71 Control unit
__________________
01 SE Granite SR20* Back to stock..... ........Just tryin to pay the damn thing off...... |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|