Hammtheman's Rb25det Powered S13...moving forward - Page 16 - TriStateTuners.com :: Home of Tristate Auto Enthusiast

hammtheman · 02-10-2014, 02:37 PM

just wish i could make progress then that.

hammtheman · 03-29-2014, 09:34 AM

so im finally home from seattle for good, but i think im buying a house so this make take a lot longer. any who r/t tuning got in the last shims for the intake side cam. it was slightly out of tomeis spec. also trans is broke down and needs a replacement second gear and syncro. hoping in the next month it will all be wrapped up and sitting in my shop giving me motivation to finish this damn thing

SSGSXR · 03-29-2014, 10:43 AM

Quote:

Originally Posted by hammtheman

so im finally home from seattle for good, but i think im buying a house so this make take a lot longer. any who r/t tuning got in the last shims for the intake side cam. it was slightly out of tomeis spec. also trans is broke down and needs a replacement second gear and syncro. hoping in the next month it will all be wrapped up and sitting in my shop giving me motivation to finish this damn thing

Only took them a year to build your block.....

Sent from my EVO using Tapatalk

hammtheman · 03-29-2014, 11:17 AM

hey man you cant rust perfection

SSGSXR · 03-29-2014, 11:38 PM

Quote:

Originally Posted by hammtheman

hey man you cant rust perfection

Your car is rusty again?

Sent from my EVO using Tapatalk

hammtheman · 03-31-2014, 06:53 PM

yeah yeah i messed up the spelling. just put an offer in on a house so the progress on the work hopefully should pick up but the spending for the project will drop....

hammtheman · 05-04-2014, 10:26 AM

got some work done on the car. i have to move it to my new garage on saturday so it kinda has to be rolling.

i welded on stops so if the intercooler ever loosens up it cant swing down.

got the passenger side over fender mounted up and riveted. its all seam sealed just needs to be sanded with a dowel rod so the seam looks uniform down the whole rear fender.

i would have finished up the drivers side but i have some rust repair i have to do on either side of the rear wheel well. typical datson/nissan

also i started putting body panels on the car so it saves the amount **** i have to pack. excuse the penis on my windshield....

i also finally checked the clearance to the door cards since i relocated the door bars. everything clears (barely) and i can still open the windows

mr_eh · 05-04-2014, 11:03 PM

rust repair? #cutdat****

hammtheman · 05-05-2014, 02:16 PM

Gotta make the car alteast look decent. Im putting in small replacement metal, seam welding and grinding smooth. Im moving my shop friday so im hoping for way more progress to get done

nsn240 · 05-14-2014, 02:22 PM

Props on the attention to detail, getting it built right! Lemme know if you need any parts, in the process of cleaning out all my 240 stuffs

hammtheman · 05-14-2014, 03:11 PM

thanks man. i have basically aquired all the parts needed besides a few little knick kacks i try to pride myself in doing this right.

hammtheman · 07-16-2014, 10:01 AM

so its been 2 months since i updated this pig and i have to say i havent dont ****. i moved to my new new house/garage and the house has taken up all my time. i attempted to pull a bigger service down to the garage and the pipe is busted under ground about 30' from the house. So right now i am currently headed up to Alaska again for work and once i return i plan on tackling that beast and getting electric run back out to my shop. I also have to run all new conduit from the service panel out to the outlets/switches.

R/T Tuning is done with the long block its being timed in the next few days, the transmission refresh hit a small issue. Im hoping when i return from Alaska I am able to get all the crap done for the electric so i can get this thing back in motion for next years drag season.

JC102024 · 07-16-2014, 02:11 PM

I came across your build, started from the beginning, and have to say i'm loving your build! Can't wait to see the end result (and hopefully a youtube video as well). Keep up the good work!

hammtheman · 08-26-2014, 06:02 PM

thank you for the kind words. im hoping to have a dyno time set up for this winter. finally picked up my motor from rt tuning and everything looks great. finally got it up on an engine stand and started to work on stuff. i started on pulling the exhuast studs to replace them with hardened ones and i snapped the very first one i went to pull. so I orded a time sert to fix everything the easy out ****ed up.

just did a small mock up of everything for photos and to be insta-famous

also got the new coil packs from super spark. heard good things from the supra guys so im giving them a try

also installed half of the mazwoxs motor mount set on the long block

PaleDSM · 08-27-2014, 10:24 AM

Nice work Mike. Looking forward to seeing the car back to stretch it's legs on the dyno.

hammtheman · 08-27-2014, 10:00 PM

Quote:

Originally Posted by PaleDSM

Nice work Mike. Looking forward to seeing the car back to stretch it's legs on the dyno.

maybe this spring it can stretch its legs on the track....maybe fastest street 240sx on the east coast???

hammtheman · 09-01-2014, 06:48 PM

got some more work done on the block. fixed the stripped manifold bolt and mounted/torqued the mani. also mounted up the wastegates, and clocked the turbo. didnt do much but its progress

time sert in the head

PaleDSM · 09-02-2014, 03:04 PM

What is the current record for a street driven car?

Shipman · 09-02-2014, 04:53 PM

Your updates make me happy

hammtheman · 09-02-2014, 06:28 PM

Quote:

Originally Posted by PaleDSM

What is the current record for a street driven car?

no way am i dipping into the 7s lol. bad call

02-10-2014, 02:37 PM	#301
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	just wish i could make progress then that. __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Those Chinese can sure build walls. but gates.... not so much apparently.....

03-29-2014, 09:34 AM	#302
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	so im finally home from seattle for good, but i think im buying a house so this make take a lot longer. any who r/t tuning got in the last shims for the intake side cam. it was slightly out of tomeis spec. also trans is broke down and needs a replacement second gear and syncro. hoping in the next month it will all be wrapped up and sitting in my shop giving me motivation to finish this damn thing __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Those Chinese can sure build walls. but gates.... not so much apparently.....

03-29-2014, 11:17 AM	#304
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	hey man you cant rust perfection __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Those Chinese can sure build walls. but gates.... not so much apparently.....

03-31-2014, 06:53 PM	#306
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	yeah yeah i messed up the spelling. just put an offer in on a house so the progress on the work hopefully should pick up but the spending for the project will drop.... __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Those Chinese can sure build walls. but gates.... not so much apparently.....

05-04-2014, 10:26 AM	#307
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	got some work done on the car. i have to move it to my new garage on saturday so it kinda has to be rolling. i welded on stops so if the intercooler ever loosens up it cant swing down. got the passenger side over fender mounted up and riveted. its all seam sealed just needs to be sanded with a dowel rod so the seam looks uniform down the whole rear fender. i would have finished up the drivers side but i have some rust repair i have to do on either side of the rear wheel well. typical datson/nissan also i started putting body panels on the car so it saves the amount **** i have to pack. excuse the penis on my windshield.... i also finally checked the clearance to the door cards since i relocated the door bars. everything clears (barely) and i can still open the windows __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Those Chinese can sure build walls. but gates.... not so much apparently.....

05-04-2014, 11:03 PM	#308
mr_eh Tri-State Addict Join Date: Dec 2005 Location: Staten Island, NY Member #1149 My Ride: Zenki S14 - Sold the SRT4 iTrader: (1)	rust repair? #cutdat**** __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. no thread for current s2000.

05-05-2014, 02:16 PM	#309
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	Gotta make the car alteast look decent. Im putting in small replacement metal, seam welding and grinding smooth. Im moving my shop friday so im hoping for way more progress to get done __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Those Chinese can sure build walls. but gates.... not so much apparently.....

05-14-2014, 02:22 PM	#310
nsn240 Tri-State Training Wheels Join Date: Mar 2009 Member #11975 My Ride: nissan iTrader: (0)	Props on the attention to detail, getting it built right! Lemme know if you need any parts, in the process of cleaning out all my 240 stuffs

05-14-2014, 03:11 PM	#311
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	thanks man. i have basically aquired all the parts needed besides a few little knick kacks i try to pride myself in doing this right. __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Those Chinese can sure build walls. but gates.... not so much apparently.....

07-16-2014, 10:01 AM	#312
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	so its been 2 months since i updated this pig and i have to say i havent dont ***. i moved to my new new house/garage and the house has taken up all my time. i attempted to pull a bigger service down to the garage and the pipe is busted under ground about 30' from the house. So right now i am currently headed up to Alaska again for work and once i return i plan on tackling that beast and getting electric run back out to my shop. I also have to run all new conduit from the service panel out to the outlets/switches. R/T Tuning is done with the long block its being timed in the next few days, the transmission refresh hit a small issue. Im hoping when i return from Alaska I am able to get all the crap done for the electric so i can get this thing back in motion for next years drag season. __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.* Those Chinese can sure build walls. but gates.... not so much apparently.....

07-16-2014, 02:11 PM	#313
JC102024 Tri-State Training Wheels Join Date: Jul 2014 Location: Downingtown, PA Member #26748 My Ride: 2007 civic si iTrader: (0)	I came across your build, started from the beginning, and have to say i'm loving your build! Can't wait to see the end result (and hopefully a youtube video as well). Keep up the good work!

08-26-2014, 06:02 PM	#314
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	thank you for the kind words. im hoping to have a dyno time set up for this winter. finally picked up my motor from rt tuning and everything looks great. finally got it up on an engine stand and started to work on stuff. i started on pulling the exhuast studs to replace them with hardened ones and i snapped the very first one i went to pull. so I orded a time sert to fix everything the easy out ***ed up. just did a small mock up of everything for photos and to be insta-famous also got the new coil packs from super spark. heard good things from the supra guys so im giving them a try also installed half of the mazwoxs motor mount set on the long block __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures.* Those Chinese can sure build walls. but gates.... not so much apparently.....

08-27-2014, 10:24 AM	#315
PaleDSM Tri-State Post Whore Join Date: Mar 2005 Location: Dublin, Pa Member #274 iTrader: (1)	Nice work Mike. Looking forward to seeing the car back to stretch it's legs on the dyno. __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. 2000 MR2 Spyder (Yellow) 2013 Hyundai Elantra

09-01-2014, 06:48 PM	#317
hammtheman Tri-State Addict Join Date: Oct 2009 Location: Boyertown, Pa Member #15004 My Ride: 1989 240sx iTrader: (2)	got some more work done on the block. fixed the stripped manifold bolt and mounted/torqued the mani. also mounted up the wastegates, and clocked the turbo. didnt do much but its progress time sert in the head __________________ 240sx Build Thread To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. Those Chinese can sure build walls. but gates.... not so much apparently.....

09-02-2014, 03:04 PM	#318
PaleDSM Tri-State Post Whore Join Date: Mar 2005 Location: Dublin, Pa Member #274 iTrader: (1)	What is the current record for a street driven car? __________________ To view links or images in signatures your post count must be 10 or greater. You currently have 0 signatures. 2000 MR2 Spyder (Yellow) 2013 Hyundai Elantra

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
RB25DET into S13	ambitiousCK	Nissan / Infiniti Talk	8	05-19-2011 09:16 PM
new member laying rubber with RB25DET powered 240	CDub	Welcome to TriStateTuners	5	08-22-2010 09:08 PM
Streeteg's Widebody, Rb25det Powered 260z	StreetEG	Member Journals	20	05-12-2010 10:52 AM
RB25DET anyone???	US_R33	Gallery	43	03-15-2006 07:32 PM