FS/FT: DSM Stock parts galore, 2g TSi, 6bolt engine, exhaust, more parts

[Ninjaneonturtle]

Parts are pick up only in Sicklerville, NJ 08081. Pics upon request. I have no time to ship unless I get a break inbetween. I might even be traveling in your vicinity on business so I'd be glad to meet you if its not too far out of the way that I'm going. PMing me is most effective way to contact me. Make reasonable offers on the parts. I would like to see this stuff go, but don't lowball me.

I will trade for a GM MAF-T or 272 cams. Even if my item is less expensive I'll add cash to it.


1995 Eagle Talon TSi FWD Automatic transmission. TITLE Attached. I'll take $250 for the shell as it sits, Minus the parts that are taken off the car. $350 with parts listed below except for the EPROM ECU.
As far as the 2g goes, its a full shell minus engine and tranny. Black/grey interior. Only thing missing is the hood. The glass is good on it minus the windsheild.
2g list:
F4A22 [Fits 2G only] Automatic transmission, no slips: $150
Stock exhaust including O2 [good for inspections] - $80
95 EPROM ECU -$200
Stock SMIC -$20
Starter -$15
A/C Compressor -$30
Intercooler piping top and bottom with 2g BOV -$15
Stock motor mounts + tranny mount no tears -$10
Front and rear O2 sensors -$20 a piece
Exterior parts!- best offer.


Engine:

6 bolt engine, needs rebuild, engine seized. Crank is still good. Needs bearings/rods/pistons. Was rebuilt w/ 50k on it. Block and cylinder head. $400
6 bolt block, needs pistons. $200
2.5 inch 02-back exhaust- $100
3 inch Buschur catback-$170
3 inch Buschur FWD downpipe-$50

1g MAF [x2] -$10
14b turbo w/ stock O2 housing, little side to side shaft play and a crushed wastegate nipple, I checked it and bent it back. Comes with O2 sensor.-$100
Blown 16g turbo, needs rebuild and exhaust turbine-$50-
450cc injectors, unknown mileage [x3 sets] -$45 a set. One set has O-rings.
88 Starion/Conquest TSi injectors ???cc's -$20
1g Non-cruise cable- $25
1g Throttle bodies ['90 TB and '91+ TB] -$25
1g red Upper intercooler hardpipe w/ elbow and semi-crushed 1g BOV-$50
Misc. DSM intercooler piping and Starion/Conquest piping- Best offer
1g stock sidemount [x2] -$20 each
88 Starion/Conquest FMIC -$35
Stocking Timing cover [used] -$10
2.5 inch test pipe -$15


Drivetrain:
1g FWD 5-speed tranny $200
ACT 2600 Pressure plate [used] -$60
6 bolt AWD flywheel + Shift fork [used, flywheel probably needs resurfacing] -$25
Slave cylinder [used] -best offer
1g Passenger side axle [used] -$25
1g Front Strut bar [silver] -$20
OEM Rear Brake Pads NIB-$25
Front EBC Green Stuff Pads NIB -$40

Interior/Electric:
91+ Non EPROM ECU, caps resoldered -$70
1g Cluster [116,416k] -$15
1g Console and 100% perfect leather shift boot -$15
Nitrous relays, wiring and switch setup is on the console, can be separated -$15
B+M Leather shift knob [no wear] $15
Driver side door trim w/ mirror switch and window switch -$10
Front seatbelt assembly [shoulder belts] $20
Window Motor [used] -best offer
A/C Fusebox -best offer
1991 TSi Owners Manual -$2
Gauge Pillar pod [Holds one gauge] $10


Misc:
Pioneer Premier head unit -$30
2 Kenwood speakers -best offer
Rockford Fosgate Punch Amplifier 160.2 [comes with Monster Power cable w/ inline fuse, Monster RCA cable and Monster Remote turn on cable] -$50

[landshark]

hey man ill be coming by tomorrow. maybe i can help take one of those gauges off ya hand

[Ninjaneonturtle]

hey man ill be coming by tomorrow. maybe i can help take one of those gauges off ya hand

I won't be around tomorrow, I'll be out looking for a tranny for my car. If you're around tomorrow evening/night then yeah you can come check it out.

[Ninjaneonturtle]

bump. I have a few more parts not in my posession yet, but I'm picking up a 95 FWD shell w/ an EPROM ECU and good interior/wheels that I'm parting out.

[filjoy2001]

hey Frank, what color is the interior on the 95 your getting?

[Ninjaneonturtle]

hey Frank, what color is the interior on the 95 your getting?

Its just the standard grey interior, but the seats are in surprisingly good shape. You have to come pick out your dibs from the lot of parts! lol.

[filjoy2001]

all i really NEED is an FPR and i think kyle is picking it up for me(not sure which one) and bringing it up to me saturday. i may want to take the drivers seat of your hands though. mine is pretty worn.

[Ninjaneonturtle]

set price bump.

I have to look and see, there's like 3 I have that adapt differently. So I might just give him all three to bring to you and then take the one that works best, then he'll bring the other two back to me.

Driver's seat has no tears in it or anything though when I went to check the car out, I'm going to pick it up tomorrow.

And is it really what you need? what you want is another story. haha

[filjoy2001]

yea normally i would agree with you. but it is something i actually need. i cant go WOT without knocking, pulling timinig, and chancing an explosion in my engine. the FPR i got on there now is not safe. MEGAN = ****

[endlessmyk]

Size of the UICP?
Also some pics, of that, shifter, console w/boot and 3gauge pod.
You don't happen to have hatch carpet would you?
I might need to pick up a few odds and ends.

[Ninjaneonturtle]

Size of the UICP?
Also some pics, of that, shifter, console w/boot and 3gauge pod.
You don't happen to have hatch carpet would you?
I might need to pick up a few odds and ends.


I might have extra hatch carpet. I'm picking up a few cars soon, and I'll have it available then. I will get picks shortly.

[Ninjaneonturtle]

http://img.photobucket.com/albums/v34/frankturtle/photo-17.jpg

http://img.photobucket.com/albums/v34/frankturtle/photo-16.jpg

The UICP is 2 inch. After looking at the 3 pod, it was cut out and plastic welded in the empty radio bezel.

[filjoy2001]

bump for a good friend

[lawdogg]

For all 8 injectors & 2 SMICs, $125 shipped?

[Ninjaneonturtle]

For all 8 injectors & 2 SMICs, $125 shipped?

The price is each.. that's per set and per intercooler. The one SMIC is spoken for already, I'm getting a 2g SMIC in exchange so that's now up for grabs. you might want to readjust your offer now though.

I can do 255 shipped for the 2 sets of injectors and 1 SMIC.

[lawdogg]

LOL sorry to lowball you, but I will pass. Sorry!

[Ninjaneonturtle]

LOL sorry to lowball you, but I will pass. Sorry!

honest mistake. no biggy. I don't need things gone at crackhead prices yet.

[Ninjaneonturtle]

partout bump!

[SpendOne]

Is the Oil Pressure gauge mechanical or electrical?? If its electrical and comes with the sender then I will take it.

[Ninjaneonturtle]

All the gauges are mechanical. I wouldn't price an electrical gauge with sender that cheap anyway.

Here's a pic of the gauge pods up closer due to request:

http://img.photobucket.com/albums/v34/frankturtle/photo-18.jpg

[Ninjaneonturtle]

more parts to the list bump.

[blackvr4]

do u have a picture of the 1G/A talon nose piece? i am very intrested, can paypal you tonight, are you willing to ship?

[Ninjaneonturtle]

do u have a picture of the 1G/A talon nose piece? i am very intrested, can paypal you tonight, are you willing to ship?

Yeah, I can ship it for extra. I'll snap a pic of it..

edit:

http://img.photobucket.com/albums/v34/frankturtle/photo-19.jpg

[blackvr4]

Yeah, I can ship it for extra. I'll snap a pic of it..

edit:

http://img.photobucket.com/albums/v34/frankturtle/photo-19.jpg

sold, tell me where to paypal the money and how much to with shipping paypal? will 20bucks cover everything?

[Ninjaneonturtle]

sold, tell me where to paypal the money and how much to with shipping paypal? will 20bucks cover everything?

$23.69 total should cover the packaging and shipping + 3% paypal fee. Its usually $13 or so to ship and buy packaging when it comes to a part like that.

paypal is: ninjaneonturtle@aim.com

pm me your address, or should I ship to the one on the paypal account?

[blackvr4]

paypaled, i sent you a message on paypal, but if u miss it, you can ship right to the paypal address. thanks alot man, i really needed this piece. you think i will get it at the end of this week?

[Ninjaneonturtle]

paypaled, i sent you a message on paypal, but if u miss it, you can ship right to the paypal address. thanks alot man, i really needed this piece. you think i will get it at the end of this week?

I'll try to ship it out tonight, if not then definately tomorrow. I'm doing a tranny swap right now so I'll see if i can squeeze it in tonight. I'll shoot you a tracking number when I do.

[blackvr4]

yea man today or tomorow it dont matter. either way if u ship tomorow ill most likely get it by friday.
thanks
good luck with the tranny swap!

[Ninjaneonturtle]

Yeah so much for luck on the tranny swap. 2g Auto tranny for sale... damn thing won't work for my application.

[Ninjaneonturtle]

2g's going to the junkyard in a week or so! get the parts while you still can.

[filjoy2001]

hey frank how many miles are on that 2g auto tranny?

[Ninjaneonturtle]

hey frank how many miles are on that 2g auto tranny?


about 170k or so, but the guy drove it from NY to Philly with no problems. No slips. 2nd gen autos hold up better than 1st gens, especially the turbo ones. I also drained the fluid out of it and it was clean. I have the torque converter for it too.

[Ninjaneonturtle]

:bump:

[Kevin]

What color is the interior kick panel that covers access to the fuse box?

[Ninjaneonturtle]

What color is the interior kick panel that covers access to the fuse box?

should be gray. I'll go check.

[Kevin]

should be gray. I'll go check.

I need that. And the plug that keeps it down. Like the thing that goes onto the bolt. I've asked too may retards on DSMtuners.com to find out what panel I'm talking about. I might have finally come across it...

[turbo4g63]

do you have the stock gray a pillar w/ no gauge pod. I want to move my boost gauge off of the a pillar and into my cluster bezel so i don't have any gauges in my face when i drive.

[Ninjaneonturtle]

the stock grey pillar I have.

[Ninjaneonturtle]

I need that. And the plug that keeps it down. Like the thing that goes onto the bolt. I've asked too may retards on DSMtuners.com to find out what panel I'm talking about. I might have finally come across it...

The panel I do have, but the plug that holds it down to the floor isn't there. I might have one laying around though. the panel is grey, it doesn't quite completely cover the fuse box though, but I guess that's close enough.

[Ninjaneonturtle]

trade bump

[Kevin]

The panel I do have, but the plug that holds it down to the floor isn't there. I might have one laying around though. the panel is grey, it doesn't quite completely cover the fuse box though, but I guess that's close enough.

Think I could get a pic so I'm sure your right?

[Ninjaneonturtle]

Think I could get a pic so I'm sure your right?

http://img.photobucket.com/albums/v34/frankturtle/photo-21.jpg

Is that right?

[Kevin]

Yep it is. I'll take it. PM me

[Ninjaneonturtle]

Yep it is. I'll take it. PM me

Wow, those guys must have been retarded. You has a PM.

[filjoy2001]

bump for friend

[Ninjaneonturtle]

bumpity bump

[turbokidd90gst]

what do you have left

[Ninjaneonturtle]

what do you have left

everything listed. I'm open to offers on the more expensive things.

[Ninjaneonturtle]

le bump.

[Lrizzel]

pm for the boost gauge i want it

[squints88]

would you take $40 for the hard IC piping without the blow off valve? Let me know I can pick it up asap!

[Kevin]

bump for an answer to my PM.

[Ninjaneonturtle]

would you take $40 for the hard IC piping without the blow off valve? Let me know I can pick it up asap!

Yeah I'll take $40 without the 1g BOV.

[filjoy2001]

bump for ninja

[K_Quay]

I will take everything you have there for $1000. Let me know.

hahaha

[K_Quay]

oh yeah bump

[Ninjaneonturtle]

I will take everything you have there for $1000. Let me know.

hahaha

:lol: The joke's on you, I sold some of my stuff, lol. List updated bump.

[Ninjaneonturtle]

bump.. noone needs to build a 6 bolt? I'll even trade for a Stratus/Breeze 2.4 DOHC engine, straight up.

[Twinz]

im interested in the exhaust...do you have any pics?

[Ninjaneonturtle]

im interested in the exhaust...do you have any pics?

I'll post them asap. which exhaust? i have 3 kinds..

[Twinz]

2.5 inch 02-back exhaust- $100
3 inch Buschur catback-$170

i only saw these 2...whats the other one?

can i have pics of both...or all three

i have a 2nd gen gsx so cant use the fwd buschur down pipe but im interested in the rest of the exhuast

[Ninjaneonturtle]

2.5 inch 02-back exhaust- $100
3 inch Buschur catback-$170

i only saw these 2...whats the other one?

can i have pics of both...or all three

i have a 2nd gen gsx so cant use the fwd buschur down pipe but im interested in the rest of the exhuast

I also have a 2nd gen FWD TSi stock exhaust. you could use the cat-back for inspection if you were interested in that also. I'm not near the exhausts till monday.

[Ninjaneonturtle]

exhaust pics:

Buschur exhaust is the larger one obviously.

http://img.photobucket.com/albums/v34/frankturtle/photo-22.jpg

http://img.photobucket.com/albums/v34/frankturtle/photo-23.jpg

http://img.photobucket.com/albums/v34/frankturtle/photo-24.jpg

[Twinz]

ok thank you i'll let you know soon

[Ninjaneonturtle]

weekend bump

[Ninjaneonturtle]

noone needs any dsm parts? I highly doubt it.

[Twinz]

was gonna pick up the 3" exhaust but im low on funds for the time being...too many other bills to worry about right now...if its still available in a while i'll prob pick it up but dont save it for me or anything...free bump

[Ninjaneonturtle]

bump..

[Ninjaneonturtle]

bump...

[RacerX3kGT]

pics of shell? whats the cond. of it?

[K20EF9]

pics of the block..?

[Ninjaneonturtle]

I'll get pics as soon as I can, the block and shell are in another location so it will give me time to get pics. The shell just has faded headlights and a dented front fender. The windsheild is no good, but the interior is 90% clean and unmolested. I'll throw in the tranny in for free, just get it off my hands. Besides that it is all there.

[K20EF9]

alright thanks man no hurry