screamingdsm
02-27-2008, 10:25 PM
1g throttle bodies 90-92 50 a piece
1g crank angle sensors, all working 40 a piece
stock turbo intake manifolds ported 50 a piece
1g coil pack for a 91+ 50 bucks
power transitors 20 a piece
isc sensor 30 bucks
1g head, 50k miles, race ported, 3g lifters 500
g4cs 2.4 block no crank 75 bucks
1g 6 bolt block, .20 over 2g pistons, 1g big rods, needs freshing up 50k, had 180 across when together 400 bucks
1g valve covers, hyundai smooth top and stock painted 20 a piece
1g hks vpc all sensors perfect working order 550 and 660 injector chip, changes the metering from mass air to speed density (map sensor) so no more air flow meter. 340
2g throttle body elbo drilled for air temp for vpc 50
afc 2 180
eprom ecu, socketed recapped and sealed 270
2 dsmchips stage 3 chips. Both setup for vpc on 550cc chip One chips setup for 650cc injectors, phantom knock code, studder box, octane reset aka all the stage 3 options
2nd chip is setup for 880cc injectors and vpc, all of above plus, dual timing maps. It has a extended pump gas map, so you can run high boost on pump gas, and a race gas map set for 10% leaner across the board and 23 degrees advance
80 bucks for both
to4e 60-1 with high output t4 p trim turbine wheel, setup for bolt on style to stock manifold, and wastegate off the manifold or turbine housing. I have the reciept from forced performance for the turbo rebuild,good for 630hp 3k miles asking 720
2g race ported manifold with tial 38mm wastegate flange welded on. Still has center divider as needed. 150
punishment racing internal wastegate block off 2.5 o2 housing 60
msd dis2 with plug and play harness 200
forced performance 272/272 cams 3k miles 400
got alot of other stuff, just call and ask
call 856-264-7432
1g crank angle sensors, all working 40 a piece
stock turbo intake manifolds ported 50 a piece
1g coil pack for a 91+ 50 bucks
power transitors 20 a piece
isc sensor 30 bucks
1g head, 50k miles, race ported, 3g lifters 500
g4cs 2.4 block no crank 75 bucks
1g 6 bolt block, .20 over 2g pistons, 1g big rods, needs freshing up 50k, had 180 across when together 400 bucks
1g valve covers, hyundai smooth top and stock painted 20 a piece
1g hks vpc all sensors perfect working order 550 and 660 injector chip, changes the metering from mass air to speed density (map sensor) so no more air flow meter. 340
2g throttle body elbo drilled for air temp for vpc 50
afc 2 180
eprom ecu, socketed recapped and sealed 270
2 dsmchips stage 3 chips. Both setup for vpc on 550cc chip One chips setup for 650cc injectors, phantom knock code, studder box, octane reset aka all the stage 3 options
2nd chip is setup for 880cc injectors and vpc, all of above plus, dual timing maps. It has a extended pump gas map, so you can run high boost on pump gas, and a race gas map set for 10% leaner across the board and 23 degrees advance
80 bucks for both
to4e 60-1 with high output t4 p trim turbine wheel, setup for bolt on style to stock manifold, and wastegate off the manifold or turbine housing. I have the reciept from forced performance for the turbo rebuild,good for 630hp 3k miles asking 720
2g race ported manifold with tial 38mm wastegate flange welded on. Still has center divider as needed. 150
punishment racing internal wastegate block off 2.5 o2 housing 60
msd dis2 with plug and play harness 200
forced performance 272/272 cams 3k miles 400
got alot of other stuff, just call and ask
call 856-264-7432