How much power are you making?

[VtechISfun]

I'm putting down 330awhp and 333 tourque (thanx to the guys over at TurboTrix for doing such a great job)

I made those numbers on 23psi and 93octane fuel.... just have some normal bolt-ons and stock clutch :cool: not too bad considering there was a person who made 350awhp on 24psi and a 20g turbo :confused: i wonder who did his tune... lol

I thought it would be a good idea to start this just to get a feel for what kinda numbers people r putting out around the area... see :eek: what the competition is like :banana:

[Rey The Great]

wrong section..and something similar to this thread already been posted

[DPancoast]

not necessarily...he's in the philly section....from philly....asking about power.....but yeah...maybe not.

Also...wtf at my bad clutch power curve..

http://i3.photobucket.com/albums/y74/pancoast_dan/MR2/MR2.jpg

[CHAOS]

there was definitely a thread on this exact topic.

[NOPSTNS]

yeah but he wants a narrower audience. he just wants to kno if any philly area peeps be rockin some high hp....

so judging by Dpancoast, i am finally not DEAD LAST in the hp department! thanks buddy!

[DPancoast]

haha that is with a TERRIBLY bad clutch dude. The videos are embarrassing.

[Buster]

No dyno numbers yet but hoping for around 330hp and 300tq. big 16g w/ supporting mods.

[NOPSTNS]

haha that is with a TERRIBLY bad clutch dude. The videos are embarrassing.



oh......


well in that case.....


:(

[VtechISfun]

No dyno numbers yet but hoping for around 330hp and 300tq. big 16g w/ supporting mods.

Sounds pretty good.... don't go blowin a tran though :roll: i hear those wrx trannys r pretty weak :(

[Buster]

Sounds pretty good.... don't go blowin a tran though :roll: i hear those wrx trannys r pretty weak :(

<--- whos on number 3? this guy! LOL... not funny

The trannies themselves arent that bad, it depends on the conditions.
My first one broke because in the 15k miles I had it i put probably 100+ launches on it practicing and ****. It just sheared 1st gear though.

My last one broke about 2 weeks ago and it was probably a stress thing from just 2 years of hard pulls. It only chipped off 2 teeth on the pinon gear.


The new one is getting nothing but 55 mph and 4k shifts LOL, until I can get the onther one PPG'd

[underpressure02]

I put down 505 on my bone stock ls/vtec at 22psi with a gt40r on a mustang dyno.

My built motor is putting out a little bit more then that. :lol:

[Mach1]

300/332...about 5 bolt-ons short of full bolt-on. Looking for 340-350 with out opening my heads or spray...then I'm popping on the Eaton. :)

[DPancoast]

I put down 505 on my bone stock ls/vtec at 22psi with a gt40r on a mustang dyno.

My built motor is putting out a little bit more then that. :lol:

:bigeek: :eek: :) wowzers.

oh......


well in that case.....


:(

haha who knows dude. Once my exhaust gets done this week, I'm going back to get new numbers. I might still be below you haha.

[HibachiZ28]

Figure stock, the engine is underrated from the factory and typically produce 310hp / 340tq. I've got a few good hp gainers and running a full second faster than my car stock, so I have no idea where I am. I do mean to get it dyno'd soon. I just had a tune and need to drop to a 160* t-stat now as well. Can't wait to get the numbers on this one.

[SovXietday]

Don't know yet, but won't be adequate until I'm over 400. This is in the Honda btw.

Camaro is stock LS1 whatever that does. Probably low 300s.

[VtechISfun]

I put down 505 on my bone stock ls/vtec at 22psi with a gt40r on a mustang dyno.

My built motor is putting out a little bit more then that. :lol:

wow dude that's insanity i would love to feel something like that one day ... boosted honda's r like sex except it needs the right partner lol... please don't slaughter me for my terrible :bigeek: attempt at a joke

but seriously though that's pretty disgusting man

:bigeek: :eek: :) wowzers.



haha who knows dude. Once my exhaust gets done this week, I'm going back to get new numbers. I might still be below you haha.

lol please tell me u'll have a new clutch in before u go in for another try :)

[wrx-auto-x]

02 wrx bugeye about 295hp at 16.86psi. no dyno yet but i know that a cobb stage 2 makes 285hp/285tq at 15.8psi so i am estimating my numbers. but not too bad for just a 3" tbe ,short ram intake, and open source tuned stage 2 map.

[rich_price]

368 rwhp / 365 rw torque .. bone stock ( 2006 LS2 GTO ) .. I can post up a dyno chart as soon as I have more than 3 posts ( TST n00b)

[BlackSSNick]

224 whp / No torque number yet

[SovXietday]

http://i3.photobucket.com/albums/y74/pancoast_dan/MR2/MR2.jpg

Toyota features the new engine in the MR2, once reaching redline, it realizes "wtf was I doing" and goes backwards to create max power. Only available in slipping clutch models.

:-p

[Willdue]

about 140ish whp? lol

[VtechISfun]

368 rwhp / 365 rw torque .. bone stock ( 2006 LS2 GTO ) .. I can post up a dyno chart as soon as I have more than 3 posts ( TST n00b)

I'd like to give u a run sometime :mrgreen: i think it'd be a good race..
what do you think?

[DPancoast]

Toyota features the new engine in the MR2, once reaching redline, it realizes "wtf was I doing" and goes backwards to create max power. Only available in slipping clutch models.


haha MR2 Salesman FTW!

[blkZ06]

Should be between 950-1050 ill let you know this weekend

[AztecTT]

Should be between 950-1050 ill let you know this weekend

****... welp, that's [/thread] lol

340rwhp "ish"...dunno torque. Just got new side mount ICs on last week, curious to see. 14.5-15.25 PSI

Just waitin for these stock turbos to go out one of these days.

Then, she becomes a project.

[JSpecV03]

never dyno'd but guessing im about the 200's with only short ram and cat back

[BradC]

never dyno'd but guessing im about the 200's with only short ram and cat back

Good luck with that one...

[SpEcRv9]

never dyno'd but guessing im about the 200's with only short ram and cat back

Good luck with that one...

i agree...

our specs get about 155whp 160wtq stock....our cars are notorious for dynoing low numbers....compared to our claimed numbers of 175hp 180tq...our motor is also not known for big gains from aftermarket products

only a few specs have reached 200whp n/a....they're fully bolted and then some...

[BradC]

i agree...

our specs get about 155whp 160wtq stock....our cars are notorious for dynoing low numbers....compared to our claimed numbers of 175hp 180tq...our motor is also not known for big gains from aftermarket products

only a few specs have reached 200whp n/a....they're fully bolted and then some...
Your car (I assume your avatar is your car) looks nice with the dark-colored stockies man.

[xEJ20x]

02 wrx bugeye about 295hp at 16.86psi. no dyno yet but i know that a cobb stage 2 makes 285hp/285tq at 15.8psi so i am estimating my numbers. but not too bad for just a 3" tbe ,short ram intake, and open source tuned stage 2 map.

I'm gonna take a shot in the dark and say you're prolly not near that.
Maybe ~240 - 250 to the wheels......unless you're running an STi motor.

[SpEcRv9]

Your car (I assume your avatar is your car) looks nice with the dark-colored stockies man.

yeah its my car...thanks!!

[mojo audi]

yea idk 295's pretty hhard to belive. thats a lot of horsepower for a car that only comes around 220hp stock i think. With just my giac chip im supposed to be around 320 crank hp and 390 ft/lbs. I also have the full exhaust, intake, front mount, boost controller and y pipe. I'm guessing at 22psi around 340whp and close to 400ft/lbs.

[rodknock02]

302awhp 322awtq 18g Low Boost Hopin For 370ish

[cmr076]

the audi is supposedly 190hp(@crank) / 207TQ and weighs in at a mere 3384lbs. :lol:

the ae86 from the factory came with a SOHC 8-valve Inline-4 Carburated motor that made a whopping 87hp @ 4800 and 85TQ :mrgreen: with the silvertop swap we should be around 150-160whp (hopefully) and the car weighs in at around 2400lb w/ me or my bro driving.

[PhillyLS1]

Should be between 950-1050 ill let you know this weekend
Which blower did you go with?
I'm only putting down close to 700 with my STS kit, I plan on going with an F1A and meth when I get home from Iraq.

[SovXietday]

Should be between 950-1050 ill let you know this weekend

I've been secretly following your build and I can no longer watch it for fear that I will try to do it myself. Damn LSXs and their potential!:eek:

[dragonfly2k3]

LOL at everyone making really high butt dyno numbers. I do not know my numbers yet, but i know they are low, i would have to guess right around 115whp or so. and about 100wtq.

[twistedlanes]

120-130 to the wheels according to my butt dyno...

[Mach1]

I'd like to give u a run sometime :mrgreen: i think it'd be a good race..
what do you think?


Don't know about you, but he should be low 13 high 12's if he can drive...not sure where you should be (know jack about evo's).

[VtechISfun]

I should be in the low 12's but that's if you have a really experienced person behind the wheel... so i still think it'd be a good one :thumbup:

[Snowboy459]

190 crank, 206ft lbs.

[JSpecV03]

i agree...

our specs get about 155whp 160wtq stock....our cars are notorious for dynoing low numbers....compared to our claimed numbers of 175hp 180tq...our motor is also not known for big gains from aftermarket products

only a few specs have reached 200whp n/a....they're fully bolted and then some...

im estimating near the 200's at the crank...but that is not WHP. im gonna dyno sometime and see

[evomike]

Ahhh turbotrix and their dyno numbers, I wonder how many other cars that day put those exact numbers down. Anyway on low boost and straight pump gas I'm at 445 whp, once the motor goes back in ill see what it'll really do

[blkZ06]

Which blower did you go with?
I'm only putting down close to 700 with my STS kit, I plan on going with an F1A and meth when I get home from Iraq.

F1C

I've been secretly following your build and I can no longer watch it for fear that I will try to do it myself. Damn LSXs and their potential!:eek:

Doo it :mrgreen:

[Charged SVTF]

216 and 170 to the wheels. Go Focus Go....woops I mean Slow Focus.....SLLLOOOWWWWWW

[BlackZ05]

http://img.photobucket.com/albums/v624/JCamaro84z/graphs.jpg
Before Test Pipes an Fixed Y-pipe.

[Mach1]

I should be in the low 12's but that's if you have a really experienced person behind the wheel... so i still think it'd be a good one :thumbup:

Then all 3 of us should go. :) I should be near mid 12's with DR's

[deb38]

ea idk 295's pretty hhard to belive. thats a lot of horsepower for a car that only comes around 220hp stock i think. With just my giac chip im supposed to be around 320 crank hp and 390 ft/lbs. I also have the full exhaust, intake, front mount, boost controller and y pipe. I'm guessing at 22psi around 340whp and close to 400ft/lbs.

You are gonna need a stage 3- and some k04's to get 340whp. Back in the day, when I was on the stock turbos and stock fueling, sans FMIC etc. I dyno'd 310/340ish (wheel).

I should be sitting at just over 400/470wheel now.

[mojo audi]

You are gonna need a stage 3- and some k04's to get 340whp. Back in the day, when I was on the stock turbos and stock fueling, sans FMIC etc. I dyno'd 310/340ish (wheel).

I should be sitting at just over 400/470wheel now.
I basiclly am stage 3- then becasue i had rt tuning replace the turbos with k03/k16's. A little bigger than the stock k03 and can supposedly create as much power as a k04

[TwilightBlueFox]

Last June I dynoed 217/275, the mods I've done since then should put me at almost 240 if you believe the manufacturers claims, but I think its more around 230. Can't wait to see what it makes when the AFR 165's go on next month!

[deb38]

I basiclly am stage 3- then becasue i had rt tuning replace the turbos with k03/k16's. A little bigger than the stock k03 and can supposedly create as much power as a k04

ahhh k03/k16...that is k04wheel in a k03 housing?

[Gregory]

Does anyone else think it's funny that our unit for measuring power is still Horse?

[mojo audi]

ahhh k03/k16...that is k04wheel in a k03 housing?

ha yep hybrid son

[VtechISfun]

Deb I saw you on campus today. Saw you in the lot and then as i was walking back to the lot i saw you turning on to market from 33rd it was around 5:30ish... that was the first time i saw your intercooler looked nice (lol and believe i was staring like a mawfocka :eek:) ... still can't get over those BBS's either sick. :thumbup:

and on a side note... wow we got quite a few people making some crazy numbers around this area... did not realize it was that many

[HatchSurfer3]

yea im gonna say between 100-110, woo hoo! Weighs in at about a whopping 2300 lbs

[rodder]

362 whp, 372 wtq... N/A in a 2800 lb truck. :mrgreen:

http://i16.photobucket.com/albums/b48/roddernj2/truck1.jpg

[mrchariybrown]

not bad for our tiny stock sti turbo's hah

http://photos-h.ak.facebook.com/photos-ak-sf2p/v159/193/11/8216198/n8216198_34711231_2906.jpg

[VtechISfun]

not bad for our tiny stock sti turbo's hah

http://photos-h.ak.facebook.com/photos-ak-sf2p/v159/193/11/8216198/n8216198_34711231_2906.jpg

that's why they make up for it with that extra half liter :roll:

[mrchariybrown]

that's why they make up for it with that extra half liter :roll:

torque ftw!

[Danronian]

My Teal Civic VX BEAST...

95 hp/ 97 lbs tq

43-60 MPG!

I love my daily driver! :) :)

Wish I had the money to make some more power from my Malibu or make a project civic... Oh well.

[AztecTT]

My Teal Civic VX BEAST...

95 hp/ 97 lbs tq

43-60 MPG!

I love my daily driver! :) :)

Wish I had the money to make some more power from my Malibu or make a project civic... Oh well.



60mpg???

[ThinkEvo2007]

TT sucks for tuning go ivey tune and ull get alot more. i had a TT tune made 343. then got an ivey tune and had over 386 to the wheels.... talk about a huge difference.




I'm putting down 330awhp and 333 tourque (thanx to the guys over at TurboTrix for doing such a great job)

I made those numbers on 23psi and 93octane fuel.... just have some normal bolt-ons and stock clutch :cool: not too bad considering there was a person who made 350awhp on 24psi and a 20g turbo :confused: i wonder who did his tune... lol

I thought it would be a good idea to start this just to get a feel for what kinda numbers people r putting out around the area... see :eek: what the competition is like :banana:

[98GSXdude]

683hp to the front wheels on the stock electric supercharger and piston snappers. All I have is an upgraded clutch bearing release valve, and ported dipstick. These motors really make power when you open them up.

[AztecTT]

683hp to the front wheels on the stock electric supercharger and piston snappers. All I have is an upgraded clutch bearing release valve, and ported dipstick. These motors really make power when you open them up.


torque steer much?

[Mach1]

My Teal Civic VX BEAST...

95 hp/ 97 lbs tq

43-60 MPG!

I love my daily driver! :) :)

Wish I had the money to make some more power from my Malibu or make a project civic... Oh well.



LOL wow, my escort lays down 125/130 and still makes 41MPG LOL

[iampakman]

stock crank figures- 115hp/122tq.
butt dyno figures- 110-115hp, 120-125tq
and still average 30MPG

[greekc6]

592 rwhp and 517tq in 88 degree weather. i wanted to break 600 damn it :mrgreen:

[Miata-Chick]

I've got 172 whp and 139 ft/lbs torque...
I'll take it.

[Scapegoat]

I've got 172 whp and 139 ft/lbs torque...
I'll take it.

that's all you need in scranton.... :o

[dragonfly2k3]

I've got 172 whp and 139 ft/lbs torque...
I'll take it.

thats alot for a miata.

[BoostdTSi91]

370hp thanks to the guys at slowboyracing and buschurracing

[Charged SVTF]

I've got 172 whp and 139 ft/lbs torque...
I'll take it.

Nice. Sounds like track and autocross heaven!

[Duffbuster243]

I've got 172 whp and 139 ft/lbs torque...
I'll take it.
Fun car to drive. I can Vouch :mrgreen:

[driftingrx5.7]

291hp 332 tq for now :) all in my rx7 :)

[TwilightBlueFox]

thats alot for a miata.

I agree thats not bad for a little miata.

[SStealth2k]

122 hp 105 ft/lbs torque

[Scapegoat]

122 hp 105 ft/lbs torque

for every two cylinders?

[Charged SVTF]

for every two cylinders?

Agreed.